TRENDnet TPE-1620WS User's Guide - Page 57

IPv6 Source IP Address, IPv6 Destination IP Address

Get TRENDnet TPE-1620WS PDF manuals and user guides View all TRENDnet TPE-1620WS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

TRENDnet User's Guide © Copyright 2013 TRENDnet. All Rights Reserved. TPE-1620WS Add IPv6 To add an IPv6 policy, use the following procedure: • Click Add IPv6, The Policy Settings page. • Enter a number in the Policy Index field. The Policy Index is a unique number within the range of 1 - 65535 which identifies the policy. This field is mandatory. • Choose the parameters to add for the policy, and enter data one or more of the parameters required for your policy. They are listed here: o VLAN ID - A unique number identifying a VLAN ranging from 1 to 4094. o 802.1p Priority - 802.1p priority level of the frame ranging from 0 to 7. o Protocol - Indicates the packet protocol ranging from 0 to 255. o IPv6 Source IP Address - Specifies the IPv6 Source IP address. o Prefix Length - Indicates the length of the Source IP ranging from 1- 128. o IPv6 Destination IP Address - Specifies the IPv6 Destination IP address. o Prefix Length - Indicates the length of the Destination IP ranging from 1- 128. o Source Layer 4 Port - Indicates the source layer 4 port ranging from 1 - 65535. o Destination Layer 4 Port - Indicates the destination layer 4 port ranging from 1 - 65535. o Policy Sequence: Enter a number in the Policy Sequence field. The Policy Sequence must be a unique number within the range of 1 65535. This field is mandatory. o Policy Action: In the Permit/Deny field, use the pull down menu to select one of the following parameters: o Deny - This selection drops ingress packets that conform to the specified Replaced-CoS or Replaced-DSCP. o Permit - This selection allows ingress packets that conform to the specified Replaced-CoS or Replaced-DSCP to be processed by the switch. Note: You must enter a selection for Deny/Permit field even if the Profile Action ID that you have entered ignores both the ReplacedDSCP and Replaced-CoS fields. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-1620WS
57
Add IPv6
To add an IPv6 policy, use the following procedure:
•
Click
Add IPv6,
The
Policy Settings
page.
•
Enter a number in the
Policy
Index
field. The
Policy Index
is a unique number
within the range of 1 – 65535 which identifies the policy. This field is
mandatory.
•
Choose the parameters to add for the policy, and enter data one or more of the
parameters required for your policy. They are listed here:
o
VLAN ID
- A unique number identifying a VLAN ranging from 1 to 4094.
o
802.1p Priority
- 802.1p priority level of the frame ranging from 0 to 7.
o
Protocol
- Indicates the packet protocol ranging from 0 to 255.
o
IPv6 Source IP Address
- Specifies the IPv6 Source IP address.
o
Prefix Length
- Indicates the length of the Source IP ranging from 1-
128.
o
IPv6 Destination IP Address
- Specifies the IPv6 Destination IP
address.
o
Prefix Length
- Indicates the length of the Destination IP ranging from
1- 128.
o
Source Layer 4 Port
- Indicates the source layer 4 port ranging from 1 -
65535.
o
Destination Layer 4 Port
- Indicates the destination layer 4 port
ranging from 1 - 65535.
o
Policy Sequence:
Enter a number in the Policy Sequence
field. The
Policy Sequence must be a unique number within the range of 1 -
65535. This field is mandatory.
o
Policy Action:
In the
Permit/Deny
field, use the pull down menu to
select one of the following parameters:
o
Deny
- This selection drops ingress packets that conform to the
specified
Replaced-CoS
or
Replaced-DSCP
.
o
Permit
- This selection allows ingress packets that conform to the
specified
Replaced-CoS
or
Replaced-DSCP
to be processed by the
switch.
Note:
You must enter a selection for
Deny/Permit
field even if the
Profile Action ID that you have entered ignores both the
Replaced-
DSCP
and
Replaced-CoS
fields.