Yamaha RX-V2065 Owner's Manual - Page 65

INTRODUCTION PREPARATION BASIC OPERATION y • When "Surround Back Speaker" is set to "None", "PLIIx Movie", "PLIIx Music" and "PLIIx Game" of the surround decode mode (page 29) are not available. Bass Crossover Frequency Choices: 40Hz, 60Hz, 80Hz*, 90Hz, 100Hz, 110Hz, 120Hz, 160Hz, 200Hz Sets the lower limit of the low-frequency component output from a speaker with a size set to "Small" (Small x 1, Small x 2) Sound with a frequency below that limit is output from a subwoofer or front speakers. If your subwoofer has a volume control or a crossover frequency control, set the volume to half or the crossover frequency at the maximum. Subwoofer Phase Choices: Normal*, Reverse Sets the phase of your subwoofer if bass sounds are lacking or unclear. Normal Reverse Select this not to change the phase of your subwoofer. Select this to reverse the phase of your subwoofer. ■ Speaker Level Adjustable range: -10.0dB to +10.0dB (0.5dB step) Defaults: 0dB (FR.L, FR.R, SWFR, PR.L, PR.R) -1.0dB (CNTR, SUR.L, SUR.R, SBL, SBR) Separately adjusts volume of each speaker so that the sounds form speakers are at the same volume at the listening position. Items to be displayed vary depending on the number of speakers connected. y • When only one surround back speaker is connected, "SB" appears instead of "SBL" and "SBR". • You can adjust the volume listening to test tones when you set "Test Tone" to "On" (on this page). • If your subwoofer has a volume control or a crossover frequency control, set the volume to half or the crossover frequency at the maximum. ■ Speaker Distance Adjusts timing at which each speaker outputs sound so that sounds from speakers reach the listening position at the same time. Set unit (Unit) first and set the distance of each speaker. Unit Choices: feet (ft)*, meters (m) feet (ft) meters (m) Displays the speaker distance in feet. Displays the speaker distance in meters. Operating various settings for this unit (Setup menu) FR.L / FR.R / CNTR / SUR.L / SUR.R / SBL / SBR / SWFR / PR.L / PR.R Adjustable range: 0.30m to 24.00m (1.0ft to 80.0ft) Defaults: 3.00m (10.0ft) (FR.L, FR.R, SWFR, PR.L, PR.R) 2.60m (8.5ft) (CNTR) 2.40m (8.0ft) (SUR.L, SUR.R, SBL, SBR) y • Available items differ depending on the "Speaker Configuration" settings (page 59). • When only one surround back speaker is connected, "SB" appears instead of "SBL" and "SBR". ■ Equalizer Adjusts sound quality and tone using a parametric graphic equalizer. EQ Type Select Choices: Auto PEQ, GEQ*, Off Selects an equalizer type. Auto PEQ GEQ Off Uses a parametric equalizer selected in "Auto Setup". Characteristics of the currently used parametric equalizer are displayed below "Auto PEQ". Uses a graphic equalizer. Press jENTER to adjust the characteristics of the graphic equalizer. Not use a graphic equalizer. GEQ Channels Front Left, Front Right, Center, Surround Left, Surround Right, Surround Back Left, Surround Back Right Choices: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.3kHz, 16kHz Adjustable range: -6.0dB to 0dB* to +6.0dB (0.5dB step) Adjusts sound quality of each speaker using a graphic equalizer. The graphic equalizer of this unit can adjust signal levels in 7 frequency ranges. To adjust the signal level within each range, press jCursor l / h to select the desired speaker while "Channel" is selected, press jCursor k / n to select the desired frequency band and then press jCursor l / h to adjust the signal level. ■ Test Tone Choices: Off*, On Switches between on and off of an oscillator that generates test tones. When "On" is selected, you can adjust the settings of "Manual Setup" while listening to a test tone. Off Not generate test tones. On Generates test tones. ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 61 En