Yamaha RX-V2065 Owner's Manual - Page 81

English, Introduction, Appendix, Preparation, Basic, Operation, Advanced

Get Yamaha RX-V2065 - AV Network Receiver PDF manuals and user guides
UPC - 027108933948
View all Yamaha RX-V2065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

INTRODUCTION PREPARATION BASIC OPERATION Troubleshooting Problem No sound is output from a specific speaker. No sound is heard from the subwoofer. No sound is heard from the surround back speakers. The audio input sources cannot be played in the desired digital audio signal format. Multi-channel playback is not available. Cause Remedy See page Output from that speaker is disabled. Check the Speaker indicators on the front panel display. If the corresponding indicator is turned off, try the following. 1) Change the input source to another one. 2) With the selected sound field program, sound is not output from that speaker. Select another sound field program. 3) "None" may have been selected for that speaker on this unit. Display "Speaker Setup" in the "Setup" menu and enables output of that speaker. 6, 24, 27, 59 The volume of that speaker is set to minimum in "Speaker Setup" in the "Setup" menu. Display "Speaker Setup" in the "Setup" menu and 61 adjust the volume (Manual Setup → Speaker Level). This unit is in the straight decode mode. Press QSTRAIGHT (or rSTRAIGHT) to turn 30 off the straight decode mode. Sound may not be output from certain Try another sound field program. 27 channels depending on input sources or sound field programs. The speaker is malfunction. Check the speaker indicators on the front panel - display. If the corresponding indicator lights up, connect another speaker and check if sound is output. If sound is not output, this unit may be malfunction. "LFE / Bass Out" is set to "Front" and a Set "LFE / Bass Out" to "Subwoofer" or "Both". 60 Dolby Digital, DTS or AAC signals is being played. "LFE / Bass Out" is set to "Subwoofer" or Set "LFE / Bass Out" to "Both". 60 "Front" and a 2-channel source is being played. The source does not contain low frequency signals. "Extended Surround" in the Option menu Set "Extended Surround" other than "Off" or "Auto". 54 is set to "Off", or an input signal does not contain a surround back flag with "Extended Surround" set to "Auto". The connected component is not set to Set the playback component properly referring to its - output the desired digital audio signals. operating instructions. The connected component is set to output Set the playback component properly referring to its - 2-ch or PCM signals. operating instructions. "Audio Output" is set to "Amplifier + Set "Audio Output" to "Amplifier". 62 TV". ADVANCED OPERATION APPENDIX English 77 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
77
En
Troubleshooting
English
INTRODUCTION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
No sound is output
from a specific
speaker.
Output from that speaker is disabled.
Check the Speaker indicators on the front panel
display. If the corresponding indicator is turned off,
try the following.
1) Change the input source to another one.
2) With the selected sound field program, sound is not
output from that speaker. Select another sound field
program.
3) “None” may have been selected for that speaker on
this unit. Display “Speaker Setup” in the “Setup”
menu and enables output of that speaker.
6, 24, 27,
59
The volume of that speaker is set to
minimum in “Speaker Setup” in the
“Setup” menu.
Display “Speaker Setup” in the “Setup” menu and
adjust the volume (Manual Setup
→
Speaker Level).
61
This unit is in the straight decode mode.
Press
Q
STRAIGHT
(or
r
STRAIGHT
) to turn
off the straight decode mode.
30
Sound may not be output from certain
channels depending on input sources or
sound field programs.
Try another sound field program.
27
The speaker is malfunction.
Check the speaker indicators on the front panel
display. If the corresponding indicator lights up,
connect another speaker and check if sound is output.
If sound is not output, this unit may be malfunction.
—
No sound is heard
from the subwoofer.
“LFE / Bass Out” is set to “Front” and a
Dolby Digital, DTS or AAC signals is
being played.
Set “LFE / Bass Out” to “Subwoofer” or “Both”.
60
“LFE / Bass Out” is set to “Subwoofer” or
“Front” and a 2-channel source is being
played.
Set “LFE / Bass Out” to “Both”.
60
The source does not contain low
frequency signals.
No sound is heard
from the surround
back speakers.
“Extended Surround” in the Option menu
is set to “Off”, or an input signal does not
contain a surround back flag with
“Extended Surround” set to “Auto”.
Set “Extended Surround” other than “Off” or “Auto”.
54
The audio input
sources cannot be
played in the desired
digital audio signal
format.
The connected component is not set to
output the desired digital audio signals.
Set the playback component properly referring to its
operating instructions.
—
Multi-channel
playback is not
available.
The connected component is set to output
2-ch or PCM signals.
Set the playback component properly referring to its
operating instructions.
—
“Audio Output” is set to “Amplifier +
TV”.
Set “Audio Output” to “Amplifier”.
62
Problem
Cause
Remedy
See
page