Yamaha RX-V2065 Owner's Manual - Page 91

After Auto Setup

Get Yamaha RX-V2065 - AV Network Receiver PDF manuals and user guides
UPC - 027108933948
View all Yamaha RX-V2065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

INTRODUCTION PREPARATION Troubleshooting After Auto Setup Error message W-1:OUT OF PHASE W-2:OVER 24m (80ft) W-3:LEVEL ERROR W-4:CHECK PRNS Cause Remedy Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. Check the polarities (+, -) of the displayed speaker. If they are correct, the speakers work properly even when this message is displayed. The distance between the speaker and the Bring the speaker within 24 m (80 ft.) area around listening position is over 24 m (80 ft). the listening position. The difference of volume level among speakers is excessive. Recheck the speaker positions and make sure all speakers are placed in a similar environment. Check the polarities (+, -) of the speakers. We recommended that you use speakers with the same or similar specifications. Adjust the output volume of the subwoofer. Presence speakers were not detected during measurement with "Extra Speaker Assignment" set to "Presence". Check the presence speaker connections and perform measurement again. If presence speakers are not connected, set the "Extra Speaker Assignment" to other than "Presence". See page 12 - - 12 - - 11, 60 BASIC OPERATION ADVANCED OPERATION APPENDIX English 87 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
8
7
En
Troubleshooting
English
INTRODUCTION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
After Auto Setup
Error message
Cause
Remedy
See
page
W-1:OUT OF PHASE
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the polarities (+, –) of the displayed speaker.
If they are correct, the speakers work properly even
when this message is displayed.
12
W-2:OVER 24m (
8
0ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker within 24 m (80 ft.) area around
the listening position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive.
Recheck the speaker positions and make sure all
speakers are placed in a similar environment.
—
Check the polarities (+, –) of the speakers.
12
We recommended that you use speakers with the
same or similar specifications.
—
Adjust the output volume of the subwoofer.
—
W-4:CHECK PRNS
Presence speakers were not detected
during measurement with “Extra Speaker
Assignment” set to “Presence”.
Check the presence speaker connections and perform
measurement again. If presence speakers are not
connected, set the “Extra Speaker Assignment” to
other than “Presence”.
11, 60