ZyXEL NWA1100 User Guide - Page 64

Apply, Table 11, LABEL, DESCRIPTION, Wireless Settings Screen

Page 64 highlights

Chapter 6 Wireless Settings Screen Table 11 Wireless > Wireless Settings: Access Point (continued) LABEL DESCRIPTION SSID Profile The SSID (Service Set IDentifier) identifies the Service Set with which a wireless station is associated. Wireless stations associating to the access point (AP) must have the same SSID. Select an SSID Profile from the drop-down list box. Channel Channel Width Note: If you are configuring the NWA from a computer connected to the wireless LAN and you change the NWA's SSID or security settings, you will lose your wireless connection when you press Apply to confirm. You must then change the wireless settings of your computer to match the NWA's new settings. Select the operating frequency/channel depending on your particular region from the drop-down list box. This field displays only when you select 802.11 b/g/n in the 802.11 Wireless Mode field. A standard 20MHz channel offers transfer speeds of up to 150Mbps whereas a 40MHz channel uses two standard channels and offers speeds of up to 300Mbps. However, not all devices support 40MHz channels. Select the channel bandwidth you want to use for your wireless network. It is recommended that you select 20/40 (20/40 MHz). This allows the NWA to adjust the channel bandwidth depending on network conditions. Select 20 MHz if you want to lessen radio interference with other wireless devices in your neighborhood. Advanced Settings Beacon Interval When a wirelessly network device sends a beacon, it includes with it a beacon interval. This specifies the time period before the device sends the beacon again. The interval tells receiving devices on the network how long they can wait in lowpower mode before waking up to handle the beacon. A high value helps save current consumption of the access point. DTIM Interval Delivery Traffic Indication Message (DTIM) is the time period after which broadcast and multicast packets are transmitted to mobile clients in the Active Power Management mode. A high DTIM value can cause clients to lose connectivity with the network. Output Power Set the output power of the NWA in this field. If there is a high density of APs in an area, decrease the output power of the NWA to reduce interference with other APs. Select one of the following Full (Full Power), 50%, 25%, 12.5% or Min (Minimum). See the product specifications for more information on your NWA's output power. Preamble Type Select Dynamic to have the AP automatically use short preamble when wireless adapters support it, otherwise the AP uses long preamble. RTS/CTS Threshold Fragmentation Select Long if you are unsure what preamble mode the wireless adapters support, and to provide more reliable communications in busy wireless networks. (Request To Send) The threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/ CTS handshake. Setting this attribute to be larger than the maximum MSDU (MAC service data unit) size turns off the RTS/CTS handshake. Setting this attribute to its smallest value (1) turns on the RTS/CTS handshake. The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. 64 NWA1100-N User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250

Chapter 6 Wireless Settings Screen
NWA1100-N User’s Guide
64
SSID Profile
The SSID (Service Set IDentifier) identifies the Service Set with which a wireless
station is associated. Wireless stations associating to the access point (AP) must
have the same SSID. Select an
SSID Profile
from the drop-down list box.
Note: If you are configuring the NWA from a computer connected to the wireless
LAN and you change the NWA’s SSID or security settings, you will lose your
wireless connection when you press
Apply
to confirm. You must then
change the wireless settings of your computer to match the NWA’s new
settings.
Channel
Select the operating frequency/channel depending on your particular region from
the drop-down list box.
Channel Width
This field displays only when you select
802.11 b/g/n
in the
802.11 Wireless
Mode
field.
A standard 20MHz channel offers transfer speeds of up to 150Mbps whereas a
40MHz channel uses two standard channels and offers speeds of up to 300Mbps.
However, not all devices support 40MHz channels.
Select the channel bandwidth you want to use for your wireless network.
It is recommended that you select
20/40
(20/40 MHz). This allows the NWA to
adjust the channel bandwidth depending on network conditions.
Select
20 MHz
if you want to lessen radio interference with other wireless devices
in your neighborhood.
Advanced Settings
Beacon Interval
When a wirelessly network device sends a beacon, it includes with it a beacon
interval. This specifies the time period before the device sends the beacon again.
The interval tells receiving devices on the network how long they can wait in
lowpower mode before waking up to handle the beacon. A high value helps save
current consumption of the access point.
DTIM Interval
Delivery Traffic Indication Message (DTIM) is the time period after which
broadcast and multicast packets are transmitted to mobile clients in the Active
Power Management mode. A high DTIM value can cause clients to lose
connectivity with the network.
Output Power
Set the output power of the NWA in this field. If there is a high density of APs in
an area, decrease the output power of the NWA to reduce interference with other
APs. Select one of the following
Full
(Full Power),
50%
,
25%
,
12.5%
or
Min
(Minimum). See the product specifications for more information on your NWA’s
output power.
Preamble Type
Select
Dynamic
to have the AP automatically use short preamble when wireless
adapters support it, otherwise the AP uses long preamble.
Select
Long
if you are unsure what preamble mode the wireless adapters support,
and to provide more reliable communications in busy wireless networks.
RTS/CTS
Threshold
(Request To Send) The threshold (number of bytes) for enabling RTS/CTS
handshake. Data with its frame size larger than this value will perform the RTS/
CTS handshake. Setting this attribute to be larger than the maximum MSDU (MAC
service data unit) size turns off the RTS/CTS handshake. Setting this attribute to
its smallest value (1) turns on the RTS/CTS handshake.
Fragmentation
The threshold (number of bytes) for the fragmentation boundary for directed
messages. It is the maximum data fragment size that can be sent.
Table 11
Wireless > Wireless Settings: Access Point (continued)
LABEL
DESCRIPTION