Home » ZyXEL Manuals » Networking » ZyXEL P-871H » Manual Viewer

ZyXEL P-871H User Guide - Page 65

sys sw bmstorm enable, sys sw mac list, Ethernet Port Setup

Get ZyXEL P-871H PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

P-871H Series User's Guide This command sets the administrator login password (up to 32 printable ASCII characters). The following example sets the login password to 54321. Figure 34 sys password Command Example ras> sys password 54321 11.5 sys sw bmstorm enable Syntax: sys sw bmstorm enable This command enables broadcast storm control on the Prestige with the specified threshold. The following example enables broadcast storm control with threshold 1 (which limits the broadcast storm packets to 15000 pps (packet per second) for a 100Mbps port or 1500 pps for a 10Mbps port). Figure 35 sys sw bmstorm enable Command Example ras> sys sw bmstorm enable 1 The rising threshold is around 15000(pps) in 100Base and 1500(pps) in 10Base. ras> 11.6 sys sw mac list Syntax: sys sw mac list This command displays the MAC address table. The following figure shows an example. Figure 36 sys sw mac list Command Example ras> sys sw mac list Index Port VID Mac Address 1 4 1 00:85:a0:01:01:04 ras> Type ------Dynamic 11.7 Ethernet Port Setup These are the commonly used sys sw commands you use to configure the Ethernet ports on the Prestige. 64 Chapter 11 Command Examples

Section	Page
P-871G Series User’s Guide	1
Copyright	2
Interference Statements and Warnings	3
Safety Warnings	4
ZyXEL Limited Warranty	5
Customer Support	6
Table of Contents	8
List of Figures	12
List of Tables	14
Preface	16
Getting to Know Your Prestige	18
1.1 Introduction	18
1.2 Software Features	18
1.3 Hardware Features	19
1.4 Internet Access Application	19
Hardware Overview	20
2.1 Hardware Connection	20
2.2 Front Panel LEDs	20
2.3 Rear Panel	21
2.3.1 VDSL Port	21
2.3.2 PHONE Port	21
2.3.3 LAN Ports	21
2.3.4 Console Port	21
2.3.5 POWER Port	22
The Web Configurator	24
3.1 Introduction	24
3.2 System Login	24
3.3 The Status Screen	25
3.3.1 Change Your Password	27
3.4 Prestige Lockout	27
3.5 Resetting the Prestige	28
3.5.1 Reload the Configuration File	28
3.6 Logging Out of the Web Configurator	29
3.7 Help	29
System Status and Port Statistics	30
4.1 Overview	30
Basic Setting	36
5.1 Overview	36
5.3 Introduction to VLANs	37
5.4 IGMP Snooping	38
VLAN	44
6.1 Introduction to IEEE 802.1Q Tagged VLAN	44
6.1.1 Forwarding Tagged and Untagged Frames	44
6.2 Select the VLAN Type	45
6.4.1 Configure a Port-based VLAN	50
Broadcast Storm Control	52
7.2 Broadcast Storm Control Setup	52
Maintenance	54
8.1.1 VDSL Chip Reset	54
8.1.2 Load Factory Defaults	54
8.1.3 Reboot System	55
8.2 Firmware and Configuration Management	55
8.2.1 Filename Conventions	56
8.2.1.1 Example FTP Commands	56
8.2.2 FTP Command Line Procedure	56
8.2.3 GUI-based FTP Clients	57
MAC Table	58
9.2 Viewing the MAC Table	59
Introduction to CLI	60
10.1 Overview	60
10.1.1 Accessing the Command Line Interface	60
10.2 The Login Screen	60
10.2.1 Command Conventions	61
10.2.2 Command Syntax Conventions	61
10.2.3 Getting Help	61
10.3 Command Summary	62
Command Examples	64
11.1 Overview	64
11.2 config save	64
11.3 ip igmpsnoop	64
11.4 sys password	64
11.5 sys sw bmstorm enable	65
11.6 sys sw mac list	65
11.7 Ethernet Port Setup	65
11.7.1 sys sw port enable	66
11.7.2 sys sw port speed	66
11.7.3 sys sw port status	66
11.7.4 sys sw qos defpri	67
11.7.5 sys sw vlan status	67
11.7.6 sys sw vlan type	67
11.7.7 sys sw vlan1q port status	68
11.7.8 sys sw vlan1q port defaultVID	68
11.7.9 sys sw vlan1q svlan list	69
11.7.10 sys sw vlan1q svlan setentry	69
11.7.11 sys sw vlan1q status	69
Setting up Your Computer’s IP Address	72
Verifying Settings	87
IP Subnetting	88
ASCII Characters	96
Index	98
Numerics	98
A	98
B	98
C	98
D	98
E	98
F	98
G	99
H	99
I	99
L	99
M	99
N	99
O	99
P	99
Q	100
R	100
S	100
T	100
U	100
V	100
W	101