ZyXEL U-1496S Plus User Guide - Page 34

Appendix B. U-1496E, U-1496P, and U-1496B can only connect

Get ZyXEL U-1496S Plus PDF manuals and user guides View all ZyXEL U-1496S Plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

will handshake in originate mode. ANSWER AT*M1 When operating over a leased line, modem will handshake in answer mode. Note: If you need two modems to automatically connect on a leased line when power is turned ON, one modem must be set to originate mode, and the other set to answer mode. These settings should be saved in a power-on default profile. LINE TYPE + DIAL-UP AT&L0 Modem is connected to dial-up telephone line. 2W LEASED AT&L1 Modem is connected to 2-wire leased line, phone jack should be plugged into the assigned `LEASED LINE' receptacle on the rear of the modem. 4W LEASED AT&L2 Modem is connected to 4-wire leased line. Plug the line in the same location as that for the 2W LEASED line. Note: For wiring information on the leased line, please refer to Appendix B. U-1496E, U-1496P, and U-1496B can only connect a 2-wire leased line to their dial-up jack. ERROR CONTROL CONTROL LEVEL Control Level Error Control Data Compression NONE AT&K0 Disabled Disabled MNP4(MNP3) AT&K1 MNP4 Disabled MNP4+MNP5 AT&K2 MNP4 MNP5 V.42(MNP4) AT&K3 V.42 or MNP4 Disabled + V.42(b)+MNP4(5) AT&K4 V.42 or MNP4 V.42bis based on V.42 or MNP5 based on MNP4 Note: S38.5=1 disables MNP5 connection. FLOW CONTROL DISABLED AT&H0 DTE flow control disabled. + CTS/RTS AT&H3 Hardware flow control CTS/RTS enabled. LOCAL XON/XOFF AT&H4 Local software flow control XON/XOFF enabled. PASS XON/XOFF AT&H5 Reserved. NEGOTIA(TION) FALLBACK + STAYS ON-LINE AT*E0 If error control negotiation fails, keep the no error control connection. DISCONNECT AT*E1 If not error control linked, disconnect the line.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
will handshake in originate mode.
ANSWER
AT*M1
When operating over a leased line, modem
will handshake in answer mode.
Note: If you need two modems to automatically connect on a leased
line when power is turned ON, one modem must be set to originate
mode, and the other set to answer mode. These settings should be
saved in a power-on default profile.
LINE TYPE
+
DIAL-UP
AT&L0
Modem is connected to dial-up telephone
line.
2W LEASED AT&L1
Modem is connected to 2-wire leased
line, phone jack should be plugged into the assigned `LEASED
LINE' receptacle on the rear of the modem.
4W LEASED AT&L2
Modem is connected to 4-wire leased
line. Plug the line in the same location as that for the 2W
LEASED line.
Note: For wiring information on the leased line, please refer to
Appendix B. U-1496E, U-1496P, and U-1496B can only connect a
2-wire leased line to their dial-up jack.
ERROR CONTROL
CONTROL LEVEL
Control Level
Error Control
Data Compression
NONE AT&K0
Disabled
Disabled
MNP4(MNP3)
AT&K1
MNP4 Disabled
MNP4+MNP5 AT&K2
MNP4 MNP5
V.42(MNP4)
AT&K3
V.42 or MNP4
Disabled
+
V.42(b)+MNP4(5)
AT&K4
V.42 or MNP4
V.42bis based
on V.42 or MNP5 based on MNP4
Note: S38.5=1 disables MNP5 connection.
FLOW CONTROL
DISABLED
AT&H0
DTE flow control disabled.
+
CTS/RTS
AT&H3
Hardware flow control CTS/RTS enabled.
LOCAL XON/XOFF AT&H4
Local software flow control
XON/XOFF enabled.
PASS XON/XOFF
AT&H5
Reserved.
NEGOTIA(TION) FALLBACK
+
STAYS ON-LINE
AT*E0
If error control negotiation fails,
keep the no error control connection.
DISCONNECT
AT*E1
If not error control linked,
disconnect the line.