ZyXEL U-1496S Plus User Guide - Page 7

Two, Modem And Fax Basics

Get ZyXEL U-1496S Plus PDF manuals and user guides View all ZyXEL U-1496S Plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Communication software controls the modem connected to the computer and directs data to and from the modem. For most cases in the PC environment, the modem is used in an asynchronous mode and the software controls the modem by the AT commands. ZyXEL modems support the extended AT command set and are compatible with most communication software packages. However, there are some unique features in the ZyXEL modem and there are a few unique commands to control them. Some communication packages need a "modem data file" to tell it which commands and features the modem supports. The floppy disk included with your modem package features sample data files for some popular communication software packages. CONNECTING TO YOUR PHONE If you would like to use a single phone line for voice and modem connections, remove your phone cable from the RJ11 junction box and plug one end of the RJ11 cable (supplied with modem) into the socket on the phone, then plug the other end of the cable to the rear panel of the modem labeled "DIAL-UP LINE" or "WALL". Finish by plugging in your phone cable to the rear panel of the modem labeled "PHONE". Please refer to the illustration in Fig. 3-3. DIAL-UP OR LEASED LINE The U-1496E and U-1496B can connect to 2-wire dial-up or leased lines only. The U-1496 and U-1496R offer you a choice of connecting to 2-wire dial-up line (more commonly known as public lines) and 2/4-wire leased lines. To use the U-1496 on a leased line, you must order and install a USOC JM8 jack. You must also specify 4-wire operation without TEK leads for the wiring option. When setting up a pair of modems for leased line point-to-point operation, one must be configured for originate mode and the other for answer mode. Both RJ11C and JM8 cables are supplied for your convenience. Chapter Two - MODEM AND FAX BASICS This chapter is intended for those who want to know the details behind modem and fax operations; what's going on behind the scenes. In addition to basic modem and fax terminology, this chapter helps users understand and use the available features. Experienced modem and fax users may wish to skip this chapter. WHAT IS A MODEM Modem is a compound word of MOdulator and DEModulator. A modem is used for computer communications. Refer to Fig. 2.1 for a standard modem setup and application. A modem translates computer data to analog signals (modulation) that can travel through the

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Communication software controls the modem connected to the
computer and directs data to and from the modem. For most cases
in the PC environment, the modem is used in an asynchronous mode
and the software controls the modem by the AT commands.
ZyXEL
modems support the extended AT command set and are compatible
with most communication software packages. However, there are
some unique features in the ZyXEL modem and there are a few
unique commands to control them.
Some communication packages
need a "modem data file" to tell it which commands and features
the modem supports. The floppy disk included with your modem
package features sample data files for some popular communication
software packages.
CONNECTING TO YOUR PHONE
If you would like to use a single phone line for voice and
modem connections, remove your phone cable from the RJ11 junction
box and plug one end of the RJ11 cable (supplied with modem) into
the socket on the phone, then plug the other end of the cable to
the rear panel of the modem labeled "DIAL-UP LINE" or "WALL".
Finish by plugging in your phone cable to the rear panel of the
modem labeled "PHONE". Please refer to the illustration in Fig.
3-3.
DIAL-UP OR LEASED LINE
The U-1496E and U-1496B can connect to 2-wire dial-up or leased
lines only. The U-1496 and U-1496R offer you a choice of
connecting to 2-wire dial-up line (more commonly known as public
lines) and 2/4-wire leased lines. To use the U-1496 on a leased
line, you must order and install a USOC JM8 jack. You must also
specify 4-wire operation without TEK leads for the wiring option.
When setting up a pair of modems for leased line point-to-point
operation, one must be configured for originate mode and the
other for answer mode. Both RJ11C and JM8 cables are supplied for
your convenience.
Chapter Two -
MODEM AND FAX BASICS
This chapter is intended for those who want to know the details behind modem and fax
operations; what's going on behind the scenes. In addition to basic modem and fax terminology,
this chapter helps users understand and use the available features.
Experienced modem and
fax users may wish to skip this chapter.
WHAT IS A MODEM
Modem is a compound word of MOdulator and DEModulator. A modem is
used for computer communications. Refer to Fig. 2.1 for a
standard modem setup and application. A modem translates computer
data to analog signals (modulation) that can travel through the