ZyXEL U-1496S Plus User Guide - Page 48

Effective only on the U-1496E and U-1496R. When Data/Voice

Get ZyXEL U-1496S Plus PDF manuals and user guides View all ZyXEL U-1496S Plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

control connection is made, used with ATV0 (S23b6), see result code table. (6) =1; Enable password protection to profile saving. When AT&W0 is issued and profile 0 in the EEPROM has this bit set, supervisory password will be requested. (5) =1; Enable Selective Reject in V.42 (4) =1; Effective only on the U-1496E and U-1496R. When Data/Voice switch is pressed, modem will dial the default number. (See *Dn, S29). (3) =1; Add 12dBm attenuation to the leased line transmission power. (See *Pn, S17b1, S49b0). (2) =1; V.26bis alternative A. (1) =1; Disable aborting from terminal during modem handshaking. (0) =1;* Use CELL 4800T trellis coded 4800 for V.32 4800. Note: Available with cellular mode, otherwise this feature is reserved. S36 Bit-mapped register, default = 000 Security function control *Gn (7,6,5) =0; Disable security function =1; Enable type 1* security, with password check. =2; Enable type 1 security, with password check and call back. =3; Enable type 2* security, with password check. =4; Enable type 2 security, with password check and call back. =5; Enable type 2 security, with password check and call back, remote site enters the call-back number. Note: * In security type 1, the remote site must be a ZyXEL modem. In security type 2, the remote site can be any other modem. Remote configuration control *Wab (1) =0; Write from local profile to remote profile. *Rab =1; Read from remote profile to local profile. *Fn (0) =0; Deny remote request for configuration. =1; Grant remote request for configuration. S37 Bit-mapped register, default = 000. For remote configuration using panel menu control. (See *Wab, *Rab) (7,6,5,4) =0-5; Local profile number. (3,2,1,0) =0-5; Remote profile number. Note: When using U-1496 panel for remote configuration, set S36 bit 1 and S37 first, then activate it in DIAGNOSTIC menu. S38 Bit-mapped register, default = 000 (7,6) Reserved. (5) =1; Disable MNP5 negotiation regardless of error control setting. (4) =1; Disable FAX answering in MULTI-AUTO mode. Hang up if a FAX call is received.. (3) =0; CD tracks carrier. =1; CD on/off sequence follows UNIX standard, CD On before connect message is sent. CD Off after last DCE response is sent. (UNIX system needs CD On to enable serial port receiving.) (See &C1, S21b4.) (2,1) Reserved. (0) =1; Enable repeat dialing of the default number if not connected. (See *Dn, S29)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
control connection is made, used with ATV0 (S23b6), see result code table.
(6)
=1;
Enable password protection to profile saving.
When AT&W0 is
issued and profile 0 in the EEPROM has this bit set, supervisory password will be requested.
(5)
=1;
Enable Selective Reject in V.42
(4)
=1;
Effective only on the U-1496E and U-1496R. When Data/Voice
switch is pressed, modem will dial the default number. (See *Dn, S29).
(3)
=1;
Add 12dBm attenuation to the leased line transmission power.
(See *Pn, S17b1, S49b0).
(2)
=1;
V.26bis alternative A.
(1)
=1;
Disable aborting from terminal during modem handshaking.
(0)
=1;*
Use CELL 4800T trellis coded 4800 for V.32 4800.
Note: Available with cellular mode, otherwise this feature is reserved.
S36
Bit-mapped register, default = 000
Security function control
*Gn
(7,6,5)
=0;
Disable security function
=1;
Enable type 1* security, with password check.
=2;
Enable type 1 security, with password check and call back.
=3;
Enable type 2* security, with password check.
=4;
Enable type 2 security, with password check and call back.
=5;
Enable type 2 security, with password check and call back,
remote site enters the call-back number.
Note: * In security type 1, the remote site must be a ZyXEL modem. In security type 2, the
remote site can be any other modem.
Remote configuration control
*Wab
(1)
=0;
Write from local profile to remote profile.
*Rab
=1;
Read from remote profile to local profile.
*Fn
(0)
=0;
Deny remote request for configuration.
=1;
Grant remote request for configuration.
S37
Bit-mapped register, default = 000.
For remote configuration using panel menu control.
(See *Wab, *Rab)
(7,6,5,4)
=0-5;
Local profile number.
(3,2,1,0)
=0-5;
Remote profile number.
Note: When using U-1496 panel for remote configuration, set S36 bit 1
and S37 first, then activate it in DIAGNOSTIC menu.
S38
Bit-mapped register, default = 000
(7,6)
Reserved.
(5)
=1;
Disable MNP5 negotiation regardless of error control setting.
(4)
=1;
Disable FAX answering in MULTI-AUTO mode. Hang up if a
FAX call is received..
(3)
=0;
CD tracks carrier.
=1;
CD on/off sequence follows UNIX standard, CD On before
connect message is sent.
CD Off after last DCE response is sent. (UNIX system needs CD On
to enable serial port receiving.) (See &C1, S21b4.)
(2,1)
Reserved.
(0)
=1;
Enable repeat dialing of the default number if not connected.
(See *Dn, S29)