ZyXEL U-1496S Plus User Guide - Page 85

Supported Commands For Voice Mode Operation

Get ZyXEL U-1496S Plus PDF manuals and user guides View all ZyXEL U-1496S Plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

FLOW CONTROL Software XON/XOFF flow control is used. SUPPORTED COMMANDS FOR VOICE MODE OPERATION AT+FCLASS= This command selects a DCE mode as follows: = 0 (Default), Data mode. = 2, Fax mode. = 8, Voice mode. Result codes: OK: ERROR: The DCE issues this result code if DCE accepts this command. The DCE issues this result code if is not permitted. AT+FCLASS? DCE will return current mode setting, followed by the OK result code. AT+FCLASS=? DCE will return permitted modes. The response is: 0,2,8 OK with between each line. ATA (with AT+FCLASS=8) This command causes DCE to answer the phone. DCE will return the VCON result code immediately. ATD (with AT+FCLASS=8) This command causes the DCE to dial a phone number. Result codes: VCON: The DCE issues this result code when the DCE has determined that the remote station is off hook. NO CARRIER: The DCE issues this result code when the DCE has continuously detected ringbacks for the amount of time specified in S7. BUSY: The DCE issues this result code when the DCE detects a busy tone. RINGING: The DCE issues this result code when the DCE detects a ringback signal.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
FLOW CONTROL
Software XON/XOFF flow control is used.
SUPPORTED COMMANDS FOR VOICE MODE OPERATION
AT+FCLASS=<mode>
This command selects a DCE mode as follows:
<mode> = 0 (Default), Data mode.
<mode> = 2, Fax mode.
<mode> = 8, Voice mode.
Result codes:
OK:
The DCE issues this result code if DCE accepts this command.
ERROR:
The DCE issues this result code if <mode> is not permitted.
AT+FCLASS?
DCE will return current mode setting, followed by the OK result code.
AT+FCLASS=?
DCE will return permitted modes. The response is:
0,2,8
OK
with <CR><LF> between each line.
ATA (with AT+FCLASS=8)
This command causes DCE to answer the phone. DCE will return the VCON result code
immediately.
ATD (with AT+FCLASS=8)
This command causes the DCE to dial a phone number.
Result codes:
VCON:
The DCE issues this result code when the DCE has determined that the
remote station is off hook.
NO CARRIER:
The DCE issues this result code when the DCE has continuously
detected ringbacks for the amount of time specified in S7.
BUSY:
The DCE issues this result code when the DCE detects a busy tone.
RINGING:
The DCE issues this result code when the DCE detects a ringback signal.