ZyXEL U-1496S Plus User Guide - Page 86

ATZ with AT+FCLASS=8

Get ZyXEL U-1496S Plus PDF manuals and user guides View all ZyXEL U-1496S Plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

ATH (with AT+FCLASS=8) This command causes the DCE to hang up the phone with the following considerations for a hang up while in voice mode: - Force the command AT+FCLASS=0, but do not destroy any of the voice parameters. - Force voice I/O device to Telco line. AT+VNH= This command causes the DCE to disable or enable automatic hang-ups to a varying degree in the DATA and FAX modes. = 0 (Default), the DCE shall not disable automatic hang-ups. = 1, the DCE shall disable automatic hang-ups. This behavior shall persist until the DTE issues ATH, ATZ, or AT+VIP command, or DTR drop. The DCE shall perform on hook on an ATH command. = 2, the DCE will disable automatic hang-ups. This behavior will persist until the DTE issues ATH, ATZ, or AT+VIP command, or DTR drop. The DCE shall not perform on hook on an ATH command. AT+VNH? DCE will return current hang up setting, followed by the OK result code. AT+VNH=? DCE will return permitted hang-up modes. The response is: 0,1,2 OK with between each line. ATZ (with AT+FCLASS=8) This command causes the DCE to enter DATA MODE (AT+FCLASS=0) and set all of the voice related parameters to their default values. VOICE MODE COMMANDS AT+VBT= This command causes the DCE to set the default DTMF/tone generation duration used in conjunction with AT+VTS command. The range of the is from 1 to 255. The units are 0.1 seconds. Result codes:

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
ATH (with AT+FCLASS=8)
This command causes the DCE to hang up the phone with the following considerations for a
hang up while in voice mode:
- Force the command AT+FCLASS=0, but do not destroy any of the voice parameters.
- Force voice I/O device to Telco line.
AT+VNH=<value>
This command causes the DCE to disable or enable automatic hang-ups to a varying degree
in the DATA and FAX modes.
<value> = 0 (Default), the DCE shall not disable automatic hang-ups.
<Value> = 1, the DCE shall disable automatic hang-ups. This behavior shall persist until the
DTE issues ATH, ATZ, or AT+VIP command, or DTR drop. The DCE shall perform on hook on
an ATH command.
<Value> = 2, the DCE will disable automatic hang-ups. This behavior will persist until the
DTE issues ATH, ATZ, or AT+VIP command, or DTR drop. The DCE shall not perform on hook
on an ATH command.
AT+VNH?
DCE will return current hang up setting, followed by the OK result code.
AT+VNH=?
DCE will return permitted hang-up modes. The response is:
0,1,2
OK
with <CR><LF> between each line.
ATZ (with AT+FCLASS=8)
This command causes the DCE to enter DATA MODE (AT+FCLASS=0) and set all of the
voice related parameters to their default values.
VOICE MODE COMMANDS
AT+VBT=<value>
This command causes the DCE to set the default DTMF/tone generation duration used in
conjunction with AT+VTS command.
The range of the <value> is from 1 to 255. The units are 0.1 seconds.
Result codes: