ZyXEL U-1496S Plus User Guide - Page 46

ZyXEL U-1496S Plus Manual

Get ZyXEL U-1496S Plus PDF manuals and user guides View all ZyXEL U-1496S Plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Mn (2,1) =0; =1; =2; =3; *En (0) =0; handshake fails. =1; Speaker always OFF. Speaker ON until carrier is detected. Speaker always ON. Speaker ON after last digit is dialed out until carrier detected. Maintain non-error control connection when error control Drop connection when error control handshake fails. S22 Reserved. S23 Bit-mapped register, default = 105 Qn (7) =0; Modem returns result code. =1; Modem does not return result code. (See also S40b1) Vn (6) =0; Display result code in numeric format. (See S35b7) =1; Display result code in verbose format. Xn (5,4,3) =0; Basic result code (0-4). (See result code table for ATXn) =1; Result code (0-5, 10-21). =2; Result code (0-6, 10-21). =3; Result code (0-5, 7-21). =4; Result code (0-21). =5; Error control result code enabled. =6; Error control result code enabled. =7; Error control result code enabled. &Pn (2) =0; Pulse dial make/break ratio=39%/61%. =1; Pulse dial make/break ratio=33%/67%. T (1) =0; Tone dial. P =1; Pulse dial. En (0) =0; Command echo disabled. =1; Command echo enabled. S24 Bit-mapped register, default = 138 Ln (7,6,5) =0-7; Speaker volume control. Nn (3,2,1) =0-7; Ring volume control. S25 Reserved. S26 RTS/CTS Delay, default = 0 Sets the delay, in 10 millisecond units, between RTS and modem's CTS response in synchronous mode. (See &Rn) S27 Bit-mapped register, default = 156 *Qn (7,6) =0; No response to poor signal quality. =1; Initiate retrain to poor signal quality. (See also S41b2) =2; Adaptive rate (auto fall-back and fall-forward) when signal quality changes. =3; Disconnect when signal quality is poor. &Hn (5,4,3) =0; Flow control disabled. =1; Reserved. =2; Reserved. =3; Hardware CTS/RTS flow control. =4; Software XON/XOFF flow control. =5; Reserved. &Kn (2,1,0) =0; No error control. =1; MNP4 (includes MNP3, see also S41b0).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Mn
(2,1)
=0;
Speaker always OFF.
=1;
Speaker ON until carrier is detected.
=2;
Speaker always ON.
=3;
Speaker ON after last digit is dialed out until carrier detected.
*En
(0)
=0;
Maintain non-error control connection when error control
handshake fails.
=1;
Drop connection when error control handshake fails.
S22
Reserved.
S23
Bit-mapped register, default = 105
Qn
(7)
=0;
Modem returns result code.
=1;
Modem does not return result code. (See also S40b1)
Vn
(6)
=0;
Display result code in numeric format. (See S35b7)
=1;
Display result code in verbose format.
Xn
(5,4,3)
=0;
Basic result code (0-4). (See result code table for ATXn)
=1;
Result code (0-5, 10-21).
=2;
Result code (0-6, 10-21).
=3;
Result code (0-5, 7-21).
=4;
Result code (0-21).
=5;
Error control result code enabled.
=6;
Error control result code enabled.
=7;
Error control result code enabled.
&Pn
(2)
=0;
Pulse dial make/break ratio=39%/61%.
=1;
Pulse dial make/break ratio=33%/67%.
T
(1)
=0;
Tone dial.
P
=1;
Pulse dial.
En
(0)
=0;
Command echo disabled.
=1;
Command echo enabled.
S24
Bit-mapped register, default = 138
Ln
(7,6,5) =0-7;
Speaker volume control.
Nn
(3,2,1) =0-7;
Ring volume control.
S25
Reserved.
S26
RTS/CTS Delay, default = 0
Sets the delay, in 10 millisecond units, between RTS and modem's CTS response in
synchronous mode. (See &Rn)
S27
Bit-mapped register, default = 156
*Qn
(7,6)
=0;
No response to poor signal quality.
=1;
Initiate retrain to poor signal quality. (See also S41b2)
=2;
Adaptive rate (auto fall-back and fall-forward) when signal
quality changes.
=3;
Disconnect when signal quality is poor.
&Hn
(5,4,3)
=0;
Flow control disabled.
=1;
Reserved.
=2;
Reserved.
=3;
Hardware CTS/RTS flow control.
=4;
Software XON/XOFF flow control.
=5;
Reserved.
&Kn
(2,1,0)
=0;
No error control.
=1;
MNP4 (includes MNP3, see also S41b0).