Home » Brother International Manuals » Multifunction Devices » Brother International MFC-9970CDW » Manual Viewer

Brother International MFC-9970CDW Advanced Users Manual - English - Page 85

Calibration, Stop/Exit, Black Start, Color Start, Use Calibration Data, Get Device Data Automatically

UPC - 012502625131

View all Brother International MFC-9970CDW manuals

Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Calibration A The output density for each color may vary depending on the environment the machine is in, such as temperature and humidity. Calibration helps you to improve the color density. a Press MENU. b Press a or b to display Printer. Press Printer. c Press a or b to display Calibration. Press Calibration. d Press Calibrate. e The machine will display Calibrate?. Press Yes to confirm. f The machine will display Completed. g Press Stop/Exit. You can reset the calibration parameters back to those set at the factory. a Press MENU. b Press a or b to display Printer. Press Printer. c Press a or b to display Calibration. Press Calibration. d Press Reset. e The machine will display Reset?. Press Yes to confirm. f The machine will display Completed. g Press Stop/Exit. Routine maintenance Note • If an error message is displayed, press Black Start or Color Start and try again. (For more information, see Error and maintenance messages in Appendix B of the Basic User's Guide.) • If you print using the Windows® printer driver, the driver will get the calibration data automatically if both Use Calibration Data and Get Device Data Automatically are on. (The default settings are on. See Advanced tab in the Software User's Guide.) • If you print using the Macintosh printer driver, you need to perform the calibration using the Status Monitor. After turning the Status Monitor on, choose Color Calibration from the Control menu. (See Status Monitor in the Software User's Guide. When the Status Monitor is open, choose Control / Color Calibration from A the menu bar.) 79

Section	Page
ADVANCED USER’S GUIDE MFC-9970CDW	1
User's Guides and where do I find it?	2
Table of Contents	3
1 General Setup	7
Memory storage	7
Volume settings	7
Ring volume	7
Beeper volume	8
Speaker volume	8
Automatic daylight savings time	9
Ecology features	9
Toner Save	9
Sleep mode	10
Deep Sleep mode	10
LCD screen	11
Setting the backlight brightness	11
Setting the Dim Timer for the backlight	11
Dial Prefix	11
Setting up the prefix number	11
Changing the prefix number	12
Mode Timer	12
2 Security features	13
Secure Function Lock 2.0	13
Setting and changing the Administrator Password	14
Setting up the password	14
Changing the password	14
Setting up and changing the Public user mode	15
Setting up and changing restricted users	15
Setting up restricted users	15
Changing user name, password or settings for restricted users	16
Reset existing restricted users	16
Turning Secure Function Lock on/off	17
Switching Users	18
Setting Lock	19
Setting up the password	19
Changing your Setting Lock password	20
Turning Setting Lock on/off	20
Restricting dialing	21
Dial pad restriction	21
One Touch restriction	21
Speed Dial restriction	21
LDAP server restriction	22
3 Sending a fax	23
Additional sending options	23
Sending faxes using multiple settings	23
Changing a 2-sided fax layout	23
Volume	24
Contrast	24
Changing Fax Resolution	24
Additional sending operations	25
Sending a fax manually	25
Manual transmission	25
Sending a fax at the end of a conversation	25
Dual access (black & white only)	26
Broadcasting (black & white only)	26
Before you begin the broadcast	26
How to broadcast a fax	27
Canceling a Broadcast in progress	27
Real Time Transmission	28
Overseas Mode	28
Delayed Fax (black & white only)	28
Delayed batch transmission (black & white only)	29
Checking and canceling waiting jobs	29
Setting your changes as the new default	30
Restoring all fax settings to the factory settings	30
Electronic cover page (black & white only)	31
Composing your own comments	31
Send a cover page for all faxes	32
Using a printed cover page	32
Polling overview	33
Polled transmit (black & white only)	33
Setup for polled transmit	33
4 Receiving a fax	34
Remote Fax Options (black & white only)	34
Receiving faxes into memory when the paper tray is empty	34
Fax Forwarding	34
Paging	35
Fax Storage	36
PC-Fax Receive	37
Changing Remote Fax Options	38
Turning off Remote Fax Options	38
Remote retrieval	39
Setting a Remote Access Code	39
Using your Remote Access Code	39
Retrieving fax messages	40
Changing the Fax Forwarding number	40
Remote fax commands	41
Additional receiving operations	42
Printing a reduced incoming fax	42
Duplex (2-sided) printing for Fax mode	42
Setting the Fax Receive Stamp (black & white only)	43
Receiving a fax at the end of a conversation	43
Setting the Print Density	44
Printing a fax from the memory	44
Polling overview	45
Polling receive	45
Sequential polling	45
Canceling a Sequential Polling Job	45
5 Dialing and storing numbers	47
Telephone line services	47
Tone or Pulse (Canada only)	47
For Fax/Tel mode only	47
Special line considerations	47
Roll over telephone lines	47
Two-line telephone system	47
Converting telephone wall outlets	47
Installing machine, external two-line TAD and two-line telephone	48
Additional dialing operations	49
Dialing access codes and credit card numbers	49
Additional ways to store numbers	50
Setting up Groups for Broadcasting	50
Options for Setting Up Groups	52
Changing Group numbers	53
Deleting Group numbers	54
6 Printing reports	55
Fax reports	55
Transmission verification report	55
Fax Journal	55
Reports	56
How to print a report	56
7 Making copies	57
Copy settings	57
Stop copying	57
Improving copy quality	57
Enlarging or reducing the image copied	58
Duplex (2-sided) Copying	59
Tray selection	60
Adjusting Brightness and Contrast	60
Brightness	60
Contrast	60
Sorting copies using the ADF	61
Making N in 1 copies (page layout)	61
If you are copying from the ADF:	62
If you are copying from the scanner glass:	62
2 in 1 ID Copy	63
Adjusting Color (Saturation)	64
Setting your changes as the new default	64
Restoring all copy settings to the factory settings	64
Setting your favorites	65
Retrieving your favorite setting	65
Rename your favorite setting	65
A Routine maintenance	66
Cleaning and checking the machine	66
Cleaning the outside of the machine	66
Cleaning the scanner	67
Cleaning the laser scanner windows	68
Cleaning the corona wires	72
Cleaning the drum unit	76
Cleaning the paper pick-up rollers	84
Calibration	85
Auto Registration	86
Registration	86
Manual Registration	86
Frequency (Color Correction)	87
Checking the Page Counters	87
Checking the remaining life of parts	88
Replacing periodic maintenance parts	88
Packing and shipping the machine	89
B Options	99
Options	99
Optional paper tray (LT-300CL)	100
Memory board	100
SO-DIMM Types	100
Installing extra memory	101
C Glossary	103
Index	107

Match case Limit results 1 per page

Routine maintenance

Calibration

The output density for each color may vary

depending on the environment the machine is

in, such as temperature and humidity.

Calibration helps you to improve the color

density.

Press

to display

Printer

Press

Printer

Press

to display

Calibration

Press

Calibration

Press

Calibrate

The machine will display

Calibrate?

Press

Yes

to confirm.

The machine will display

Completed

Press

Stop/Exit

You can reset the calibration parameters

back to those set at the factory.

Press

to display

Printer

Press

Printer

Press

to display

Calibration

Press

Calibration

Press

Reset

The machine will display

Reset?

Press

Yes

to confirm.

The machine will display

Completed

Press

Stop/Exit

Note

•

If an error message is displayed, press

Black Start

Color Start

and try again.

(For more information, see

Error and maintenance messages

Appendix B

of the

Basic User's Guide

•

If you print using the Windows

printer

driver, the driver will get the calibration

data automatically if both

Use Calibration Data

and

Get Device Data Automatically

are on.

(The default settings are on. See

Advanced tab

in the

Software User's

Guide

•

If you print using the Macintosh printer

driver, you need to perform the calibration

using the

Status Monitor

. After turning

the

Status Monitor

on, choose Color

Calibration from the Control menu. (See

Status Monitor

in the

Software User's

Guide

. When the

Status Monitor

is open,

choose

Control / Color Calibration

from

the menu bar.)