Home » Cisco Manuals » Wireless » Cisco G1 » Manual Viewer

Cisco G1 Installation Guide - Page 23

Installing a GBIC-NPE-G1

UPC - 746320679488

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

66774 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Installing a GBIC-NPE-G1 Use the instructions in this section to install a GBIC in the NPE-G1. Figure 7-11 Installing a GBIC in the NPE-G1 2 5 1 1 GBIC 2 Alignment groove 3 GBIC port 0/1 3 ETHERNET 0/1 RX GBIC TX 4 GIGABIT LINK ETHERNET 0/2 RJ45 EN RX GBIC 4 GBIC port 0/2 5 Plug Step 1 Turn the GBIC so the label side is up and the alignment groove is down. Note The GBIC is keyed so that it cannot be inserted incorrectly. Step 2 Insert the GBIC into GBIC port 0/1, 0/2, or 0/3. Repeat this step if you are installing more than one GBIC. Note Do not remove the GBIC plugs until you are ready to install the cables. You are finished installing the GBICs. For more information on cabling or specifications, see the "Gigabit Ethernet GBIC Connection Equipment" section on page 5-13. Note We strongly recommend cleaning all optical fiber connections before connecting optical cables to equipment. For information about cleaning optical connectors, see the Inspection and Cleaning Procedures for Fiber-Optic Connections document and the Compressed Air Cleaning Issues for Fiber-Optic Connections document. Go to the "Inserting the NPE-G1 or NPE-G2 into the Router" section on page 7-28 for instructions on installing the NPE-G1 or NPE-G2 in the chassis. OL-4448-12 Network Processing Engine and Network Services Engine Installation and Configuration 7-23

Section	Page
NPE-G1 and NPE-G2 Installation and Configuration Information	1
Preparing for an Upgrade	2
Copying the Configuration File	4
Copying the Configuration File to a Flash Disk or PC Card	4
Copying the Configuration File to a TFTP Server	5
Copying the Configuration File Using a PC	7
Removing the Network Processing Engine	7
Ensuring Easy Access to the Router	8
Powering Down the Router and Disconnecting Input Power	8
Powering Down the Router	8
Disconnecting AC-Input Power from a Cisco 7200 VXR Router	9
Disconnecting AC-Input Power from a Cisco uBR7246VXR Router	10
Disconnecting AC-Input Power from a Cisco uBR7225VXR Router	11
Disconnecting DC-Input Power from a Cisco 7200 VXR Router	11
Disconnecting DC-Input Power from a Cisco uBR7246VXR Router	13
Removing the NPE or NSE-1	16
Installing the NPE-G1 or NPE-G2	18
Basic Guidelines	18
Installing a CompactFlash Disk	19
Installing a USB Flash Memory Module or eToken-NPE-G2	19
Installing an SFP Module-NPE-G2	20
Installing a GBIC-NPE-G1	23
Replacing the DIMM on the NPE-G2	24
Upgrading the SDRAM SODIMMs on the NPE-G1 (Optional)	26
Removing a SODIMM	26
Installing a SDRAM SODIMM	27
Inserting the NPE-G1 or NPE-G2 into the Router	28
Attaching the Rear Cable-Management Brackets and Cables (Optional)	29
Installing the NPE-G1 or NPE-G2 Cable-Management Brackets	29
Installing the Rear Cable-Management Brackets on a Front-Mounted Router (Optional)	31
Installing the Rear Cable-Management Brackets on a Rear-Mounted Router (Optional)	32
Installing the Default Cable-Management Bracket on a Cisco uBR7246VXR Router (Optional)	34
Reconnecting Input Power and Powering Up the Router	35
Reconnecting AC-Input Power to the Cisco 7200 VXR Router	35
Reconnecting AC-Input Power to the Cisco uBR7246VXR Router	37
Reconnecting AC-Input Power to the Cisco uBR7225VXR Router	38
Reconnecting DC-Input Power to the Cisco 7200 VXR Router	38
Reconnecting DC-Input Power to a Cisco uBR7246VXR Router	41
Powering Up the Router	45
Enabling the Second Processor on the NPE-G1	46
Error Messages	47
Using show Commands Associated with the mpf Command	47
Using the show interface stats Command	48
Using the show ip interface Command	48
Using the show mpf cpu Command	49
Using the show mpf cpu history Command	49
Using the show mpf interface Command	50
Using the show mpf ip exact-route Command	51
Using the show mpf punt Command	51
Using the show version Command	51
Copying the Saved Configuration to NVRAM	52
Copying the Saved Configuration File from a Flash Disk or PC Card	53
Copying the Saved Configuration File from the CompactFlash Disk	53
Downloading the Saved Configuration from the TFTP Server	54
Auxiliary and Console Port Information	56
Configuring an Auxiliary Port to Receive Console Port Messages	56
Configuring the Native Gigabit Ethernet Interfaces	56
Changing the Media Type of the Native Gigabit Ethernet GBIC, SFP, or RJ-45 Ports	56
Configuring the Interface Transmission and Speed Modes	57
Sample Configuration for the Gigabit Ethernet Interfaces	57
Debugging	58
Resetting the Interface	58
Clearing Counters	59
Using show Commands to Check the Installation	59
Upgrading the Cisco IOS Image and the Boot Helper (Boot Loader) Image	62
Upgrading ROMmon on the NPE-G1 or NPE-G2	63
Using the show rom-monitor Command and ROMmon CLI showmon Commands	64
Using the upgrade rom-monitor file Command	64
Changing Preferences to Choose the Other ROMmon Image	65
Troubleshooting the Upgrade	65
ROMmon Upgrade Error Messages	66
Upgrading FPGA on the NPE-G2	67
Troubleshooting the NPE-G1 or NPE-G2	67