Home » Cisco Manuals » Wireless » Cisco G1 » Manual Viewer

Cisco G1 Installation Guide - Page 48

Using the show interface stats Command, show interface stats, show ip interface

UPC - 746320679488

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Enabling the Second Processor on the NPE-G1 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Using the show interface stats Command Use the show interface stats command for information about the interface. Router# show interface stats GigabitEthernet0/1 Switching path Pkts In Processor 33090 Route cache 2 Multi-Processor Fwding 1004 Total 34096 Chars In 6424353 116 158632 6583101 Pkts Out 86353 0 5004 91357 Chars Out 8645650 0 790632 9436282 Using the show ip interface Command Use the show ip interface command to get information about the specific interface port. Router# show ip interface g0/3 GigabitEthernet0/3 is up, line protocol is up Internet address is 155.1.1.1/16 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP Feature Fast switching turbo vector IP VPN Flow CEF switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is enabled, using route map PBR Network address translation is disabled BGP Policy Mapping is disabled IP Multi-Processor Forwarding is enabled IP Input features, "PBR", are not supported by MPF and are IGNORED IP Output features, "NetFlow", are not supported by MPF and are IGNORED 7-48 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12

Section	Page
NPE-G1 and NPE-G2 Installation and Configuration Information	1
Preparing for an Upgrade	2
Copying the Configuration File	4
Copying the Configuration File to a Flash Disk or PC Card	4
Copying the Configuration File to a TFTP Server	5
Copying the Configuration File Using a PC	7
Removing the Network Processing Engine	7
Ensuring Easy Access to the Router	8
Powering Down the Router and Disconnecting Input Power	8
Powering Down the Router	8
Disconnecting AC-Input Power from a Cisco 7200 VXR Router	9
Disconnecting AC-Input Power from a Cisco uBR7246VXR Router	10
Disconnecting AC-Input Power from a Cisco uBR7225VXR Router	11
Disconnecting DC-Input Power from a Cisco 7200 VXR Router	11
Disconnecting DC-Input Power from a Cisco uBR7246VXR Router	13
Removing the NPE or NSE-1	16
Installing the NPE-G1 or NPE-G2	18
Basic Guidelines	18
Installing a CompactFlash Disk	19
Installing a USB Flash Memory Module or eToken-NPE-G2	19
Installing an SFP Module-NPE-G2	20
Installing a GBIC-NPE-G1	23
Replacing the DIMM on the NPE-G2	24
Upgrading the SDRAM SODIMMs on the NPE-G1 (Optional)	26
Removing a SODIMM	26
Installing a SDRAM SODIMM	27
Inserting the NPE-G1 or NPE-G2 into the Router	28
Attaching the Rear Cable-Management Brackets and Cables (Optional)	29
Installing the NPE-G1 or NPE-G2 Cable-Management Brackets	29
Installing the Rear Cable-Management Brackets on a Front-Mounted Router (Optional)	31
Installing the Rear Cable-Management Brackets on a Rear-Mounted Router (Optional)	32
Installing the Default Cable-Management Bracket on a Cisco uBR7246VXR Router (Optional)	34
Reconnecting Input Power and Powering Up the Router	35
Reconnecting AC-Input Power to the Cisco 7200 VXR Router	35
Reconnecting AC-Input Power to the Cisco uBR7246VXR Router	37
Reconnecting AC-Input Power to the Cisco uBR7225VXR Router	38
Reconnecting DC-Input Power to the Cisco 7200 VXR Router	38
Reconnecting DC-Input Power to a Cisco uBR7246VXR Router	41
Powering Up the Router	45
Enabling the Second Processor on the NPE-G1	46
Error Messages	47
Using show Commands Associated with the mpf Command	47
Using the show interface stats Command	48
Using the show ip interface Command	48
Using the show mpf cpu Command	49
Using the show mpf cpu history Command	49
Using the show mpf interface Command	50
Using the show mpf ip exact-route Command	51
Using the show mpf punt Command	51
Using the show version Command	51
Copying the Saved Configuration to NVRAM	52
Copying the Saved Configuration File from a Flash Disk or PC Card	53
Copying the Saved Configuration File from the CompactFlash Disk	53
Downloading the Saved Configuration from the TFTP Server	54
Auxiliary and Console Port Information	56
Configuring an Auxiliary Port to Receive Console Port Messages	56
Configuring the Native Gigabit Ethernet Interfaces	56
Changing the Media Type of the Native Gigabit Ethernet GBIC, SFP, or RJ-45 Ports	56
Configuring the Interface Transmission and Speed Modes	57
Sample Configuration for the Gigabit Ethernet Interfaces	57
Debugging	58
Resetting the Interface	58
Clearing Counters	59
Using show Commands to Check the Installation	59
Upgrading the Cisco IOS Image and the Boot Helper (Boot Loader) Image	62
Upgrading ROMmon on the NPE-G1 or NPE-G2	63
Using the show rom-monitor Command and ROMmon CLI showmon Commands	64
Using the upgrade rom-monitor file Command	64
Changing Preferences to Choose the Other ROMmon Image	65
Troubleshooting the Upgrade	65
ROMmon Upgrade Error Messages	66
Upgrading FPGA on the NPE-G2	67
Troubleshooting the NPE-G1 or NPE-G2	67

Match case Limit results 1 per page

7-48

Network Processing Engine and Network Services Engine Installation and Configuration

OL-4448-12

Chapter 7

NPE-G1 and NPE-G2 Installation and Configuration Information

Enabling the Second Processor on the NPE-G1

Using the show interface stats Command

Use the

show interface stats

command for information about the interface.

Router#

show interface stats

GigabitEthernet0/1

Switching path

Pkts In

Chars In

Pkts Out

Chars Out

Processor

33090

6424353

86353

8645650

Route cache

116

Multi-Processor Fwding

1004

158632

5004

790632

Total

34096

6583101

91357

9436282

Using the show ip interface Command

Use the

show ip interface

command to get information about the specific interface port.

Router#

show ip interface g0/3

GigabitEthernet0/3 is up, line protocol is up

Internet address is 155.1.1.1/16

Broadcast address is 255.255.255.255

Address determined by setup command

MTU is 1500 bytes

Helper address is not set

Directed broadcast forwarding is disabled

Outgoing access list is not set

Inbound access list is not set

Proxy ARP is enabled

Local Proxy ARP is disabled

Security level is default

Split horizon is enabled

ICMP redirects are always sent

ICMP unreachables are always sent

ICMP mask replies are never sent

IP fast switching is enabled

IP fast switching on the same interface is disabled

IP Flow switching is disabled

IP CEF switching is enabled

IP Feature Fast switching turbo vector

IP VPN Flow CEF switching turbo vector

IP multicast fast switching is enabled

IP multicast distributed fast switching is disabled

IP route-cache flags are Fast, CEF

Router Discovery is disabled

IP output packet accounting is disabled

IP access violation accounting is disabled

TCP/IP header compression is disabled

RTP/IP header compression is disabled

Policy routing is enabled, using route map PBR

Network address translation is disabled

BGP Policy Mapping is disabled

IP Multi-Processor Forwarding is enabled

IP Input features, "PBR",

are not supported by MPF and are IGNORED

IP Output features, "NetFlow",

are not supported by MPF and are IGNORED