Home » Cisco Manuals » Wireless » Cisco G1 » Manual Viewer

Cisco G1 Installation Guide - Page 66

ROMmon Upgrade Error Messages

UPC - 746320679488

Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Troubleshooting the Upgrade Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information ROMmon Upgrade Error Messages One if these error message appears when the upgrade has failed or if the upgrade image is corrupted: • ROMmon image is not compatible with the ReadOnly image: Router: upgrade rom-monitor file tftp://00.0.00.0/biff/C7200_NPEG2_RMFUR.srec Loading biff/C7200_NPEG2_RMFUR.srec from 00.0.00.0 (via GigabitEthernet0/1): OK - 392348 bytes] ROMMON upgrade aborted; new ROMMON image version is not compatible with ReadOnly • ROMmon upgrade image is too big: Router: upgrade rom-monitor file tftp://00.0.00.0/biff/C7200_NPEG2_RMFUR.srec Loading biff/C7200_NPEG2_RMFUR.srec from 00.0.00.0 (via GigabitEthernet0/1): OK - 392348 bytes] ROMMON upgrade aborted; new ROMMON is too big • Hardware does not support ROMmon upgrade: Router: upgrade rom-monitor file tftp://00.0.00.0/biff/C7200_NPEG2_RMFUR.srec Loading biff/C7200_NPEG2_RMFUR.srec from 00.0.00.0 (via GigabitEthernet0/1): OK - 392348 bytes] ROMMON upgrade aborted; Current ROMMON does not support upgrade capability • Upgrade command with incorrect file type: NPEG1-10# upgrade rom-monitor file tftp://00.0.00.0/biff/C7200_NPEG2_BOOT_ROM.bin from 00.0.00.0 (via GigabitEthernet0/1 OK - 524288 bytes] %Error:not srec file • A boot of a corrupted upgrade image: System Bootstrap, Version 12.2(20031011:151758) [biff-npeg2-fur 135], DEVELOPMENT SOFTWARE Copyright (c) 1994-2003 by cisco Systems, Inc. Upgrade ROMMON corrupted. Falling to ReadOnly ROMMON ROM:Rebooted by watchdog hard reset C7200 platform with 1048576 Kbytes of main memory Readonly ROMMON initialized 7-66 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12

Section	Page
NPE-G1 and NPE-G2 Installation and Configuration Information	1
Preparing for an Upgrade	2
Copying the Configuration File	4
Copying the Configuration File to a Flash Disk or PC Card	4
Copying the Configuration File to a TFTP Server	5
Copying the Configuration File Using a PC	7
Removing the Network Processing Engine	7
Ensuring Easy Access to the Router	8
Powering Down the Router and Disconnecting Input Power	8
Powering Down the Router	8
Disconnecting AC-Input Power from a Cisco 7200 VXR Router	9
Disconnecting AC-Input Power from a Cisco uBR7246VXR Router	10
Disconnecting AC-Input Power from a Cisco uBR7225VXR Router	11
Disconnecting DC-Input Power from a Cisco 7200 VXR Router	11
Disconnecting DC-Input Power from a Cisco uBR7246VXR Router	13
Removing the NPE or NSE-1	16
Installing the NPE-G1 or NPE-G2	18
Basic Guidelines	18
Installing a CompactFlash Disk	19
Installing a USB Flash Memory Module or eToken-NPE-G2	19
Installing an SFP Module-NPE-G2	20
Installing a GBIC-NPE-G1	23
Replacing the DIMM on the NPE-G2	24
Upgrading the SDRAM SODIMMs on the NPE-G1 (Optional)	26
Removing a SODIMM	26
Installing a SDRAM SODIMM	27
Inserting the NPE-G1 or NPE-G2 into the Router	28
Attaching the Rear Cable-Management Brackets and Cables (Optional)	29
Installing the NPE-G1 or NPE-G2 Cable-Management Brackets	29
Installing the Rear Cable-Management Brackets on a Front-Mounted Router (Optional)	31
Installing the Rear Cable-Management Brackets on a Rear-Mounted Router (Optional)	32
Installing the Default Cable-Management Bracket on a Cisco uBR7246VXR Router (Optional)	34
Reconnecting Input Power and Powering Up the Router	35
Reconnecting AC-Input Power to the Cisco 7200 VXR Router	35
Reconnecting AC-Input Power to the Cisco uBR7246VXR Router	37
Reconnecting AC-Input Power to the Cisco uBR7225VXR Router	38
Reconnecting DC-Input Power to the Cisco 7200 VXR Router	38
Reconnecting DC-Input Power to a Cisco uBR7246VXR Router	41
Powering Up the Router	45
Enabling the Second Processor on the NPE-G1	46
Error Messages	47
Using show Commands Associated with the mpf Command	47
Using the show interface stats Command	48
Using the show ip interface Command	48
Using the show mpf cpu Command	49
Using the show mpf cpu history Command	49
Using the show mpf interface Command	50
Using the show mpf ip exact-route Command	51
Using the show mpf punt Command	51
Using the show version Command	51
Copying the Saved Configuration to NVRAM	52
Copying the Saved Configuration File from a Flash Disk or PC Card	53
Copying the Saved Configuration File from the CompactFlash Disk	53
Downloading the Saved Configuration from the TFTP Server	54
Auxiliary and Console Port Information	56
Configuring an Auxiliary Port to Receive Console Port Messages	56
Configuring the Native Gigabit Ethernet Interfaces	56
Changing the Media Type of the Native Gigabit Ethernet GBIC, SFP, or RJ-45 Ports	56
Configuring the Interface Transmission and Speed Modes	57
Sample Configuration for the Gigabit Ethernet Interfaces	57
Debugging	58
Resetting the Interface	58
Clearing Counters	59
Using show Commands to Check the Installation	59
Upgrading the Cisco IOS Image and the Boot Helper (Boot Loader) Image	62
Upgrading ROMmon on the NPE-G1 or NPE-G2	63
Using the show rom-monitor Command and ROMmon CLI showmon Commands	64
Using the upgrade rom-monitor file Command	64
Changing Preferences to Choose the Other ROMmon Image	65
Troubleshooting the Upgrade	65
ROMmon Upgrade Error Messages	66
Upgrading FPGA on the NPE-G2	67
Troubleshooting the NPE-G1 or NPE-G2	67