Cisco G1 Installation Guide - Page 36

Connecting AC-Input Power to a Cisco 7200 VXR Router, POWER OK LED

Get Cisco G1 - Network Processing Engine G1 PDF manuals and user guides
UPC - 746320679488
View all Cisco G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Installing the NPE-G1 or NPE-G2 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Figure 7-24 Connecting AC-Input Power to a Cisco 7200 VXR Router 1 84398 2 3 4 5 1 Power switch 2 AC power cable 3 POWER OK LED 4 Cable-retention clip 5 Hole for nylon cable tie Step 4 Plug the AC power supply cable into the AC power source. Note For Cisco 7200 VXR routers, each AC-input power supply operating at 120 VAC requires a minimum of 5A service. We recommend powering the Cisco 7200 VXR routers from a 120 VAC, 15A receptacle U.S. (240 VAC, 10A international) at the power source. Step 5 Repeat Step 1 through Step 4 if a second power supply is installed. This completes the steps for reconnecting AC-input power to a Cisco 7200 VXR router. Proceed to the "Powering Up the Router" section on page 7-45. 7-36 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
7-36
Network Processing Engine and Network Services Engine Installation and Configuration
OL-4448-12
Chapter 7
NPE-G1 and NPE-G2 Installation and Configuration Information
Installing the NPE-G1 or NPE-G2
Figure 7-24
Connecting AC-Input Power to a Cisco 7200 VXR Router
Step 4
Plug the AC power supply cable into the AC power source.
Note
For Cisco 7200 VXR routers, each AC-input power supply operating at 120 VAC requires a
minimum of 5A service.
We recommend powering the Cisco 7200 VXR routers from a 120 VAC, 15A receptacle U.S.
(240 VAC, 10A international) at the power source.
Step 5
Repeat Step 1 through Step 4 if a second power supply is installed.
This completes the steps for reconnecting AC-input power to a Cisco 7200 VXR router. Proceed to the
“Powering Up the Router” section on page 7-45
.
1
Power switch
4
Cable-retention clip
2
AC power cable
5
Hole for nylon cable tie
3
POWER OK LED
84398
1
2
3
5
4