Cisco G1 Installation Guide - Page 65

Changing Preferences to Choose the Other ROMmon Image, Troubleshooting the Upgrade

Get Cisco G1 - Network Processing Engine G1 PDF manuals and user guides
UPC - 746320679488
View all Cisco G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Troubleshooting the Upgrade Running new upgrade for first time System Bootstrap, Version 12.2(20031011:151758) [biff] Copyright (c) 1994-2003 by cisco Systems, Inc. ROM:Rebooted by watchdog hard reset C7200 platform with 1048576 Kbytes of main memory Upgrade ROMMON initialized rommon 1 > Note It is advisable to load a known good Cisco IOS image after a ROMmon upgrade. Changing Preferences to Choose the Other ROMmon Image To use the other ROMmon image, use one of the following commands to make the change depending on whether you are in Cisco IOS or in ROMmon: • In Cisco IOS, use the upgrade rom-monitor preference command to change to the other ROMmon image: upgrade rom-monitor preference [readonly | upgrade] Example: Router: upgrade rom-monitor preference readonly You are about to mark ReadOnly region of ROMMON for the highest boot preference. Proceed? [confirm] Done! Router must be reloaded for this to take effect. • In ROMmon, use the ROMmon CLI rommon-pref command to change to the other ROMmon image: rommon-pref [readonly | upgrade] Example: rommon 2 > rommon-pref readonly Troubleshooting the Upgrade This section contains sample error messages that appear if an upgrade fails, or if an upgrade is successful, but the upgrade image is corrupted. OL-4448-12 Network Processing Engine and Network Services Engine Installation and Configuration 7-65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
7-65
Network Processing Engine and Network Services Engine Installation and Configuration
OL-4448-12
Chapter 7
NPE-G1 and NPE-G2 Installation and Configuration Information
Troubleshooting the Upgrade
Running new upgrade for first time
System Bootstrap, Version 12.2(20031011:151758) [biff]
Copyright (c) 1994-2003 by cisco Systems, Inc.
ROM:Rebooted by watchdog hard reset
C7200 platform with 1048576 Kbytes of main memory
Upgrade ROMMON initialized
rommon 1 >
Note
It is advisable to load a known good Cisco IOS image after a ROMmon upgrade.
Changing Preferences to Choose the Other ROMmon Image
To use the other ROMmon image, use one of the following commands to make the change depending on
whether you are in Cisco IOS or in ROMmon:
•
In Cisco IOS, use the
upgrade rom-monitor preference
command to change to the other ROMmon
image:
upgrade rom-monitor preference
[
readonly | upgrade
]
Example:
Router:
upgrade rom-monitor preference readonly
You are about to mark ReadOnly region of ROMMON for the highest boot preference.
Proceed? [confirm]
Done! Router must be reloaded for this to take effect.
•
In ROMmon, use the ROMmon CLI
rommon-pref
command to change to the other ROMmon
image:
rommon-pref
[
readonly | upgrade
]
Example:
rommon 2 >
rommon-pref readonly
Troubleshooting the Upgrade
This section contains sample error messages that appear if an upgrade fails, or if an upgrade is
successful, but the upgrade image is corrupted.