Epson EPL-N2000 User Manual - Page 42

Toner Save Mode, Auto Continue

Get Epson EPL-N2000 PDF manuals and user guides View all Epson EPL-N2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

EPL-N2000 driver settings (continued) Time-out Various settings from 5 to 300 seconds (60 sec. default) Sets the amount of time the printer waits to receive data before terminating an incomplete print job; after the time-out period, another print job can print. Toner Save Mode ON OFF Sets the amount of toner used in your print job. If you're printing a draft copy, set to ON to use around 50% less toner for a lighter printout. Low Power ON Consumption OFF Sets the printer to enter a power-saving standby mode if it is not used for 30 minutes. (The printer takes about 1 minute to warm up after exiting standby mode.) Auto Continue ON OFF Sets the printer to use Auto Continue mode to continue printing 5 seconds after recovering from a print overrun or insufficient memory error. It is best to leave Auto continue OFF so you are alerted to errors; then you must press the Continue button on the control panel to resume. If you'll be away from the printer and are aware of possible errors, you can turn on Auto Continue mode. Printer Options tab Memory 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 36, 38, 40, 44, 52, 68 MB Specifies the amount of memory installed in the printer. Increase the number if you add memory to your printer. Printing With the Windows Printer Drivers 2-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Printing With the Windows Printer Drivers
2-11
Time-out
Various settings from 5
to 300 seconds
(60 sec. default)
Sets the amount of time the
printer waits to receive data
before terminating an
incomplete print job; after the
time-out period, another
print job can print.
Toner Save Mode
ON
OFF
Sets the amount of toner used
in your print job. If you're
printing a draft copy, set to
ON to use around 50% less
toner for a lighter printout.
Low Power
Consumption
ON
OFF
Sets the printer to enter a
power-saving standby mode
if it is not used for 30 minutes.
(The printer takes about 1
minute to warm up after
exiting standby mode.)
Auto Continue
ON
OFF
Sets the printer to use Auto
Continue mode to continue
printing 5 seconds after
recovering from a print
overrun or insufficient
memory error. It is best to
leave Auto continue OFF so
you are alerted to errors; then
you must press the Continue
button on the control panel
to resume. If you'll be away
from the printer and are
aware of possible errors, you
can turn on Auto Continue
mode.
Printer Options tab
Memory
4, 6, 8, 10, 12, 14, 16,
18, 20, 22, 24, 28, 36,
38, 40, 44, 52, 68 MB
Specifies the amount of
memory installed in the
printer. Increase the number if
you add memory to your
printer.
EPL-N2000 driver settings (continued)