HP StorageWorks 1606 HP StorageWorks FOS 6.3.0b Release Notes (5697-0360, Apri - Page 17

DC SAN Backbone and DC04 SAN Director blade support, Power supply requirements for Director blades

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

DC SAN Backbone and DC04 SAN Director blade support FOS 6.3.0a is fully qualified and supports the DC Director blades listed in Table 3. Table 3 DC Director blade support matrix Director blade FC8-16 FC8-32 FC8-48 FC10-6 Number of blades Supported with FOS 6.0.0b or later with any mix, with up to eight blades of each type on the DC SAN Backbone Director. There are no intermix restrictions. The DC04 SAN Director requires FOS 6.2.0a or later, and supports up to four blades. FC4-16IP (iSCSI blade) Not supported with the DC SAN Backbone Director or DC04 SAN Director FR4-18i (FCIP/FC Router blade) Supported with FOS 6.0.0b or later, with a maximum of four blades of this type on the DC SAN Backbone Director. Up to eight FR4-18i blades can be installed if they are used only for FC FastWrite or FCIP without routing on the DC SAN Backbone Director. The DC04 SAN Director requires FOS 6.2.0a or later, and supports up to four blades. FS8-18 (DC Switch Encryption FC blade) Supported with FOS 6.2.0b or later, with a maximum of four blades of this type on the DC SAN Backbone Director or DC04 SAN Director FX8-24 (DC SAN Director Multiprotocol Extension Blade) FCOE10-24 (DC SAN Director Switch 10/24 FCoE Blade) Supported with FOS 6.3.0x, with a maximum of two blades per director. The DC SAN Director Switch 10/24 FCoE Blade can be installed in the same chassis only with FC8-xx and/or FC10-6 blades. It is not supported in the chassis with any other blades. Power supply requirements for Director blades Table 4 lists power supply requirements for Director blades to provide full redundancy (220 VAC power is assumed). HP StorageWorks FOS 6.3.0b Release Notes 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
DC SAN Backbone and DC04 SAN Director blade support
FOS 6.3.0a is fully qualified and supports the DC Director blades listed in
Table 3
.
Table 3 DC Director blade support matrix
Number of blades
Director blade
Supported with FOS 6.0.0b or later with any mix, with up
to eight blades of each type on the DC SAN Backbone
Director. There are no intermix restrictions. The DC04 SAN
Director requires FOS 6.2.0a or later, and supports up to
four blades.
FC8-16
FC8-32
FC8-48
FC10-6
Not supported with the DC SAN Backbone Director or
DC04 SAN Director
FC4-16IP (iSCSI blade)
Supported with FOS 6.0.0b or later, with a maximum of
four blades of this type on the DC SAN Backbone Director.
Up to eight FR4-18i blades can be installed if they are
used only for FC FastWrite or FCIP without routing on the
DC SAN Backbone Director. The DC04 SAN Director
requires FOS 6.2.0a or later, and supports up to four
blades.
FR4-18i (FCIP/FC Router blade)
Supported with FOS 6.2.0b or later, with a maximum of
four blades of this type on the DC SAN Backbone Director
or DC04 SAN Director
FS8-18 (DC Switch Encryption FC blade)
Supported with FOS 6.3.0x, with a maximum of two blades
per director. The DC SAN Director Switch 10/24 FCoE
Blade can be installed in the same chassis only with FC8-
xx
and/or FC10-6 blades. It is not supported in the chassis
with any other blades.
FX8-24 (DC SAN Director Multiprotocol Extension
Blade)
FCOE10-24 (DC SAN Director Switch 10/24
FCoE Blade)
Power supply requirements for Director blades
Table 4
lists power supply requirements for Director blades to provide full redundancy (220 VAC
power is assumed).
HP StorageWorks FOS 6.3.0b Release Notes
17