HP StorageWorks 1606 HP StorageWorks FOS 6.3.0b Release Notes (5697-0360, Apri - Page 53

Hosts on 4Gb SAN switch for HP c-Class BladeSystem in Access

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Fixed in FOS 6.3.0 If configdownload is performed via DCFM, switch authentication failure may be seen. Workaround prior to code change: Issue hafailover or hareboot. Add FIP version 0 handling. Fixed in FOS 6.3.0 Address configdownload problems. Fixed in FOS 6.3.0 Due to race condition, daemons may panic during FID deletion and Fixed in FOS 6.3.0 creating without significant time delay in between. Cold-failover within Port group for F_Port didn't happen on Access Gateway (AG). Fixed in FOS 6.3.0 Supportsave may show parity errors on disabled ports. Fixed in FOS 6.3.0 Switch Admin: Merge status dialog should display the status and timestamp of last merge for FCoE Login. Fixed in FOS 6.3.0 Switch panic in kernel while access an iu that has already timedout and freed. Fixed in FOS 6.3.0 Hosts on 4Gb SAN switch for HP c-Class BladeSystem in Access Gateway-mode lost their targets when failover happened from 1 trunk group (with primary ports) to another trunk group (with shared area ports) on 8Gb 48 port blade of DC SAN Director. Fixed in FOS 6.3.0 WebTools shows no SFP details for CEE interfaces. Fixed in FOS 6.3.0 Workaround prior to code change: Use the CLI interface. On Enabling LLDP status and assigning FCoE priority bits globally, is Fixed in FOS 6.3.0 not getting reflected in Port Admin window. Confusing error message when copying a source configuration from a remote server. Fixed in FOS 6.3.0 Workaround prior to code change: Do clean-up before downloading a new CEE configuration: 1. In cmsh, run "write erase" to clear startup-config. 2. Reboot switch by running "reboot" on FOS prompt. 3. In cmsh, use "copy" command to copy backup configuration into running-config. Defect ID: DEFECT000247893 Summary: Port Auto Disable - Ports outside of given range are being enabled. Fixed in FOS 6.3.0 Workaround prior to code change: Enable and disable port auto disable for ports one at a time. IPv6 Address dropped from ag --show. Fixed in FOS 6.3.0 Workaround prior to code change: Issue switchdisable/enable causes the IPv6 Address again to be presented. Port statistics details are not getting refreshed for EX ports. Fixed in FOS 6.3.0 HP StorageWorks FOS 6.3.0b Release Notes 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Fixed in FOS 6.3.0
Workaround prior to code change:
Issue hafailover or hareboot.
If configdownload is performed via DCFM, switch authentication failure
may be seen.
Fixed in FOS 6.3.0
Add FIP version 0 handling.
Fixed in FOS 6.3.0
Address configdownload problems.
Fixed in FOS 6.3.0
Due to race condition, daemons may panic during FID deletion and
creating without significant time delay in between.
Fixed in FOS 6.3.0
Cold-failover within Port group for F_Port didn't happen on Access
Gateway (AG).
Fixed in FOS 6.3.0
Supportsave may show parity errors on disabled ports.
Fixed in FOS 6.3.0
Switch Admin: Merge status dialog should display the status and
timestamp of last merge for FCoE Login.
Fixed in FOS 6.3.0
Switch panic in kernel while access an iu that has already timedout
and freed.
Fixed in FOS 6.3.0
Hosts on 4Gb SAN switch for HP c-Class BladeSystem in Access
Gateway-mode lost their targets when failover happened from 1 trunk
group (with primary ports) to another trunk group (with shared area
ports) on 8Gb 48 port blade of DC SAN Director.
Fixed in FOS 6.3.0
Workaround prior to code change:
Use the CLI interface.
WebTools shows no SFP details for CEE interfaces.
Fixed in FOS 6.3.0
On Enabling LLDP status and assigning FCoE priority bits globally, is
not getting reflected in Port Admin window.
Fixed in FOS 6.3.0
Workaround prior to code change:
Do clean-up before downloading a
new CEE configuration: 1. In cmsh,
run "write erase" to clear
startup-config. 2. Reboot switch by
running "reboot" on FOS prompt. 3.
In cmsh, use "copy" command to
copy backup configuration into
running-config.
Confusing error message when copying a source configuration from
a remote server.
Fixed in FOS 6.3.0
Workaround prior to code change:
Enable and disable port auto disable
for ports one at a time.
Defect ID: DEFECT000247893 Summary: Port Auto Disable - Ports
outside of given range are being enabled.
Fixed in FOS 6.3.0
Workaround prior to code change:
Issue switchdisable/enable causes the
IPv6 Address again to be presented.
IPv6 Address dropped from ag --show.
Fixed in FOS 6.3.0
Port statistics details are not getting refreshed for EX ports.
HP StorageWorks FOS 6.3.0b Release Notes
53