HP StorageWorks 1606 HP StorageWorks FOS 6.3.0b Release Notes (5697-0360, Apri - Page 60

Optimized SERDES setting for Brocade 8Gb SAN Switch

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Switch Admin: Policies which are not chosen are showned in confirm- Fixed in FOS 6.3.0 ation page of ACL Policy configuration wizard. When attempting to swap ports from the GUI, the operation may fail Fixed in FOS 6.3.0 due to HTTP 500 error. Agd aborted due to *** glibc detected *** free(): invalid next size Fixed in FOS 6.3.0 (fast). DWDM link unable to sync up before port is enabled at correct speed. Fixed in FOS 6.3.0 Bad SFP triggered i2c access cause issues on port/slot disaplay and Fixed in FOS 6.3.0 cpu load on 4/256 SAN Director. Cryptocfg show transshow when issued without any outstanding transactions displayed Operation "failed" with an incorrect cause. Fixed in FOS 6.3.0 Sequence of creating two TI zones, not saving the change and then modifying the attributes with the "zone --add" command results in misconfigured attributes that will cause software verify on remote switches when changes are commited. Fixed in FOS 6.3.0 Workaround prior to code change: Other methods of creating TI Zones and modifying the definitions work seamlessly. Its just this odd set of steps which produce the failing condition. When creating multiple TI zones, they should be saved before modifying the attributes. Can clean up problem by using zone --add to modify the attributes again after the save. Can also delete and recreate TI zone. Specific call to CEE library results in gradual memory leak. Fixed in FOS 6.3.0 Getting ms_ficon errors on console of core DC SAN Director in McDATA interop after reboots. Fixed in FOS 6.3.0 Configdownload fails with Lsan tag download failed: Duplicate tag. Fixed in FOS 6.3.0 Workaround prior to code change: Use CLI to add the tag names back onto the FCR switch. In Interopmode 2 mode, FC address is shown without offset in switch.html and portshow (cli), but shown with offset in switchshow. Fixed in FOS 6.3.0 Ipaddrset command to set Lance GE ports IP address is non-responsive. Must reboot active CP to activate IP. Fixed in FOS 6.3.0 Workaround prior to code change: The following should work. Following any removal or relocation of an encryption blade from any chassis slot, do an hafailover to cause the standby CP to become active. This should be done even if no change in chassis IP addresses is required as other problems could be otherwise encountered, depending on network configuration. Optimized SERDES setting for Brocade 8Gb SAN Switch for BladeSystem c-Class. Fixed in FOS 6.3.0 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Fixed in FOS 6.3.0
Switch Admin: Policies which are not chosen are showned in confirm-
ation page of ACL Policy configuration wizard.
Fixed in FOS 6.3.0
When attempting to swap ports from the GUI, the operation may fail
due to HTTP 500 error.
Fixed in FOS 6.3.0
Agd aborted due to *** glibc detected *** free(): invalid next size
(fast).
Fixed in FOS 6.3.0
DWDM link unable to sync up before port is enabled at correct speed.
Fixed in FOS 6.3.0
Bad SFP triggered i2c access cause issues on port/slot disaplay and
cpu load on 4/256 SAN Director.
Fixed in FOS 6.3.0
Cryptocfg show transshow when issued without any outstanding
transactions displayed Operation "failed" with an incorrect cause.
Fixed in FOS 6.3.0
Workaround prior to code change:
Other methods of creating TI Zones
and modifying the definitions work
seamlessly. Its just this odd set of steps
which produce the failing condition.
When creating multiple TI zones, they
should be saved before modifying the
attributes. Can clean up problem by
using zone --add to modify the
attributes again after the save. Can
also delete and recreate TI zone.
Sequence of creating two TI zones, not saving the change and then
modifying the attributes with the "zone --add" command results in
misconfigured attributes that will cause software verify on remote
switches when changes are commited.
Fixed in FOS 6.3.0
Specific call to CEE library results in gradual memory leak.
Fixed in FOS 6.3.0
Getting ms_ficon errors on console of core DC SAN Director in
McDATA interop after reboots.
Fixed in FOS 6.3.0
Workaround prior to code change:
Use CLI to add the tag names back
onto the FCR switch.
Configdownload fails with Lsan tag download failed: Duplicate tag.
Fixed in FOS 6.3.0
In Interopmode 2 mode, FC address is shown without offset in
switch.html and portshow (cli), but shown with offset in switchshow.
Fixed in FOS 6.3.0
Workaround prior to code change:
The following should work. Following
any removal or relocation of an
encryption blade from any chassis
slot, do an hafailover to cause the
standby CP to become active. This
should be done even if no change in
chassis IP addresses is required as
other problems could be otherwise
encountered, depending on network
configuration.
Ipaddrset command to set Lance GE ports IP address is non-responsive.
Must reboot active CP to activate IP.
Fixed in FOS 6.3.0
Optimized SERDES setting for Brocade 8Gb SAN Switch for
BladeSystem c-Class.
60