IBM 8479 User Reference - Page 100

Explanation, Action, Message, Description, The number entered in the unbind command was not

Get IBM 8479 - Eserver xSeries 200 PDF manuals and user guides
UPC - 087944653912
View all IBM 8479 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Table 13. NetWare driver messages for the Ethernet controller. Message Duplicate slot numbers detected. Description Explanation: An attempt has been made to bind the same slot number more than once. 'xxx' is not supported for AFT team. Action: Check the slot numbers entered during the bind. Adapter slot numbers must be valid and unique. If the problem persists, contact your network supplier. Explanation: A bind command has been issued for adapters not supported by AFT.NLM. Primary and Secondary adapters do not match. AFT group is not created. Action: Make sure that you attempt to bind only adapters supported by AFT.NLM. Explanation: A bind command was entered for an adapter team that is a combination of system and client adapters. An AFT team must be a grouping of the same classification of adapter. Action: Verify that all the adapters bound in a team are of the same classification. Requested number of Secondary cards are not found. Explanation: The number of adapters specified in the bind command could not be located. Action: Verify the numbers and slot locations of the adapters to be bound. If the problem persists, contact your network supplier. Failed to create AFT group. Make sure that the drivers for supported adapters are loaded, primary adapter is bound to protocols, and secondary adapter is not bound to any protocols. Explanation: Binding of protocol failed. Protocol is either not bound to any adapter or is bound to more than one adapter in the group. Action: Ensure that the protocol is bound to only adapter in an AFT team. Error identifying slot numbers for the Explanation: The mapping between the board name entered and the slot specified board names. number for an adapter could not be established. Action: Check the board name for the adapter before issuing the bind command. If the problem persists, contact your network supplier. Can't unbind specified slot from AFT group. Make sure that the slot you specified is for the primary adapter in an AFT group. Explanation: The number entered in the unbind command was not the primary adapter in an AFT group. Action: Reissue the unbind command and specify the slot number for the primary adapter. LAN adapter at slot nnnn (Port 0xaa) failed to reset. Check the state of the adapter. Explanation: The adapter that you specified could not be initialized. Action: 1. Load the driver for the supported adapter. 2. Check that the adapter is seated properly in the slot and try loading the AFT module again. AFT is not supported on this version of NetWare. Failed to allocate resources tags. If the problem persists, contact your network supplier. Explanation: The NetWare on your system is not a version supported by AFT. Action: Load and bind AFT only on supported versions of NetWare (currently version 4.11 and above). Explanation: An unknown error has occurred when trying to allocate needed resources for the AFT module. Action: Check system configuration. If the problem persists, contact your network supplier. 86 IBM xSeries 200: User's Reference

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
86
IBM xSeries 200: User’s Reference
Duplicate slot numbers detected.
Explanation:
An attempt has been made to bind the same slot number more
than once.
Action:
Check the slot numbers entered during the bind. Adapter slot numbers
must be valid and unique. If the problem persists, contact your
network
supplier.
’
xxx
’ is not supported for AFT team.
Explanation:
A bind command has been issued for adapters not supported by
AFT.NLM.
Action:
Make sure that you attempt to bind only adapters supported by
AFT.NLM.
Primary and Secondary adapters do
not match. AFT group is not created.
Explanation:
A bind command was entered for an adapter team that is a
combination of system and client adapters. An AFT team must be a grouping of
the same classification of adapter.
Action:
Verify that all the adapters bound in a team are of the same
classification.
Requested number of Secondary
cards are not found.
Explanation:
The number of adapters specified in the bind command could
not be located.
Action:
Verify the numbers and slot locations of the adapters to be bound. If
the problem persists, contact your network supplier.
Failed to create AFT group. Make
sure that the drivers for supported
adapters are loaded, primary adapter
is bound to protocols, and secondary
adapter is not bound to any protocols.
Explanation:
Binding of protocol failed. Protocol is either not bound to any
adapter or is bound to more than one adapter in the group.
Action:
Ensure that the protocol is bound to only adapter in an AFT team.
Error identifying slot numbers for the
specified board names.
Explanation:
The mapping between the board name entered and the slot
number for an adapter could not be established.
Action:
Check the board name for the adapter before issuing the bind
command. If the problem persists, contact your network supplier.
Can’t unbind specified slot from AFT
group. Make sure that the slot you
specified is for the primary adapter in
an AFT group.
Explanation:
The number entered in the unbind command was not the
primary adapter in an AFT group.
Action:
Reissue the unbind command and specify the slot number for the
primary adapter.
LAN adapter at slot
nnnn
(Port 0x
aa
)
failed to reset. Check the state of the
adapter.
Explanation:
The adapter that you specified could not be initialized.
Action:
1.
Load the driver for the supported adapter.
2.
Check that the adapter is seated properly in the slot and try loading the
AFT module again.
If the problem persists, contact your network supplier.
AFT is not supported on this version
of NetWare.
Explanation:
The NetWare on your system is not a version supported by AFT.
Action:
Load and bind AFT only on supported versions of NetWare (currently
version 4.11 and above).
Failed to allocate resources tags.
Explanation:
An unknown error has occurred when trying to allocate needed
resources for the AFT module.
Action:
Check system configuration. If the problem persists, contact your
network supplier.
Table 13. NetWare driver messages for the Ethernet controller.
Message
Description