JVC GY-DV5000U GY-DV5000U 3-CCD Professional DV Camcorder 92 page instruction - Page 28

7. SHOOTING OPERATION 7-1 Basic Recording Operation 3. OPEN knob EDITSEARCH FILTER 1 3200K 2 5600K 1/8 ND .3 5600K .4 5600K 1/64 ND SHUTTER STATUS MONITOR MENU AUTO IRIS FULL AUTO BACK L NORMAL SPOT L BLACK LOLUX STRETCH NORMAL COMPRESS MODE VTR CAM POWER VTR ON OFF OPEN CH-1 AUDIO LEVEL CH-2 LCD BRIGHT FRONT REAR CH-1 CH-2 AUDIO INPUT AUDIO SELECT CH-1 CH-2 AUTO MANUAL DISPLAY PULL OPEN POWER VTR ON OFF 1. 7, 8, 9, MODE VTR CAM 2. 6. Focusing ring EDITSEARCH FILTER 1 3200K 2 5600K 1/8 ND .3 5600K .4 5600K 1/64 ND SHUTTER STATUS MONITOR MENU AUTO IRIS FULL AUTO BACK L NORMAL SPOT L BLACK LOLUX STRETCH NORMAL COMPRESS MODE VTR CAM POWER VTR ON OFF CH-1 AUDIO LEVEL CH-2 CH A CH 6. Zoom ring 7. 8. 9. VTR trigger button 1. Set the POWER switch to ON. ● Power is supplied to the unit. 2. The CAM indicator lights up. The GY-DV5000 is in the Camera mode when the CAM indicator is on. 3. Slide the OPEN switch on the top section to open the cassette cover. 4. Insert a videocassette into the cassette insertion slot. ● Ensure that the erasure-prevention switch on the back of the cassette is set to REC and insert a videocassette properly. When the cassette is inserted, the tape is loaded and the unit enters the record-standby mode. ● Slowly close the cassette cover. MEMO: ● Use a standard DV videocassette or a MiniDV videocassette. (When a DVCAM cassette is used for recording, longer recording can be performed than the time indicated on the DVCAM cassette. For the recording time, regard the remaining tape indication displayed on the LCD or in the viewfinder as a guide.) ● Following loading of the cassette and when the POWER switch is turned ON/OFF, the built-in head cleaner will emit a sound while operating. This does not indicate a malfunction. ● After the cassette cover is closed, it takes about 10 seconds before the unit is ready for recording. 5. Adjust the camera section settings and the white balance. ☞ See "Camera Settings" on page 45. ☞ See "White Balance Adjustment" on page 48. 6. Point the camera at the subject and determine the angle of view and focus with the zoom lever and the focusing ring. 7. Start recording. Press the VTR trigger button on the GY-DV5000 to start recording. Once recording has started, the BACK TALLY lamp on the rear section of the unit and the tally lamp on the viewfinder light red, and the REC indication in the viewfinder lights green. MEMO: The lightening conditions of the BACK TALLY lamp on the rear section of the unit and the tally lamp on the viewfinder can be changed by setting the BACK TALLY and FRONT TALLY items on the OTHERS (2/2) menu screen. 8. TALLY lamp OFF ZEBRA ON SKIN AREA AUTO WHITE ACCU FOCUS VTR AUDIO LEVELE CH-1 5 7. 8. 9. VTR trigger button 52 7. SHOOTING OPERATION 7-1 Basic Recording Operation (Cont'd) BATT REC ALARM 7.8 8. TALLY lamp 7. 8. 9. VTR trigger button 8. To stop recording: Press the VTR trigger button on the unit or on the lens section again. The TALLY lamp and REC indicator lamp go out and the unit enters the record-standby mode. When the VTR trigger button is pressed, the unit enters the record-standby mode after rewinding the tape for about 2 seconds (back-spacing). 9. To restart recording: Press the VTR trigger button on the GY-DV5000 or lens. 10.Ending recording: Press the VTR trigger button to enter the record-standby mode and perform the following operations as required. ■ When it is required to unload the videocassette: 1 Slide the OPEN knob to open the cassette cover. 2 Press the EJECT button to take out the videocassette. ■ When the power should be turned off Set the POWER switch to OFF. When the camera is not going to be used for a long period, detach the battery pack. About the QUICK REC START Mode If the VTR trigger button is pressed immediately after the videocassette is inserted, the mode becomes the QUICK REC START mode that enables quick start of recording. However, when shooting starts in the middle of the tape, a blank space appears as the new scene will not be linked smoothly with the previous image. Also, the time code does not continue. (Some overlap may also occur.) This function does not work during DV signal input. 7.8. TALLY lamp OFF ZEBRA ON SKIN AREA AUTO WHITE ACCU FOCUS VTR AUDIO LEVELE CH-1 5 7. 8. 9. VTR trigger button CAUTION: ● The unit enters the record standby mode automatically at TAPE END. If this mode continues for 3 or 30 minutes, the mode switches to the tape protect mode. ☞ See "LONG PAUSE TIME item on the OTHERS (1/2) menu screen" on page 77. ● If the VTR trigger button is pressed very quickly and repeatedly, or the POWER switch is moved immediately after the trigger button is pressed, the viewfinder REC indicator lamp may blink and the GY-DV5000 may not enter the record mode. To remedy this condition set the POWER switch to OFF and wait for 5 seconds or more before turning the power on again. ● A neat transition to the next recorded scene cannot be guaranteed if a recording is ended by turning the POWER switch or DC power supply OFF, or by removing the battery pack. ● Trial-shooting is always recommended before recording important events to confirm the recording is satisfactory. ● The microphone may pick up the sound of the lens' iris if the iris is changed abruptly or the iris is manually moved abruptly during recording. If the sound is found annoying, please purchase an optional microphone in order to move the microphone away from the lens or ensure that the iris is not changed abruptly during shooting. 53