Kyocera TASKalfa 180 180/220 Operation Guide Rev-2 - Page 47

How to Load Originals, IMPORTANT, Preparation before Use, OPERATION GUIDE

Get Kyocera TASKalfa 180 PDF manuals and user guides View all Kyocera TASKalfa 180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Preparation before Use How to Load Originals IMPORTANT: Before loading originals, be sure that there are no originals left on the original eject table. Originals left on the original eject table may cause the new originals to jam. 2 1 Adjust the original width guides to fit the originals. NOTE: Before setting originals, make sure that there are no originals remaining on the original eject table. Originals left on the eject table may cause other originals to jam. When setting multiple originals at one time, be sure to use originals of the same size. It is, possible, however to use different size originals of the same width (for example, 11 x 17" (Ledger) and 11 x 8 1/2" or A4 and A3 at the same time in the auto selection mode. Refer to Chapter 4 Auto Selection Mode.) 2 Arrange the originals in order and set them face up (front side up for 2-sided originals) on the original table. IMPORTANT: Be sure to set only a number of originals that does not exceed the level indicator located inside the rear original insert guide. If you set originals exceeding the specified number, the originals may jam. OPERATION GUIDE 2-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Preparation before Use
OPERATION GUIDE
2-15
2
How to Load Originals
IMPORTANT:
Before loading originals, be sure that there are no originals left on the original eject table.
Originals left on the original eject table may cause the new originals to jam.
1
Adjust the original width guides to fit the originals.
NOTE:
Before setting originals, make sure that there
are no originals remaining on the original eject table.
Originals left on the eject table may cause other
originals to jam.
When setting multiple originals at one time, be sure to
use originals of the same size. It is, possible, however
to use different size originals of the same width (for
example, 11 x 17" (Ledger) and 11 x 8
1/2
" or A4 and
A3 at the same time in the auto selection mode. Refer
to
Chapter 4 Auto Selection Mode
.)
2
Arrange the originals in order and set them face up
(front side up for 2-sided originals) on the original
table.
IMPORTANT:
Be sure to set only a number of originals
that does not exceed the level indicator located inside
the rear original insert guide. If you set originals
exceeding the specified number, the originals may jam.