Onkyo HT-R640 Owner Manual - Page 42

Speaker Con, guration

Get Onkyo HT-R640 PDF manuals and user guides View all Onkyo HT-R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

First Time Setup-Continued Speaker Configuration 2 With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. The following crossover frequencies can be specified: Full Band, 40 Hz, 50 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz, 150 Hz, 200 Hz. Specify Full Band for speakers that can output low-frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speakers' manuals to determine the optimum crossover frequencies. 3 1 2 STANDBY/ON REMOTE MODE RECEIVER DVD TAPE/AMP INPUT SELECTOR M D/CDR 1 2 3 C D HDD V1 V2 V3 4 5 6 TV V4 MULTI CH DVD 7 8 9 VCR TAPE TUNER 10 11 +10 0 C D 12 CABLE CLR SAT D TUN --/--- ENT DIMMER SLEEP TV VOL INPUT GUIDE TOP MENU CH DISC ALBUM VOL PREVIOUS MENU PLAYLIST/CAT ENTER MUTING PLAYLIST/CAT RETURN SETUP 2-10 1, 11 4 5 1 AMP RECEIVER Press the [RECEIVER] or [AMP] button followed by the [SETUP] button. The main menu appears onscreen. SETUP Use the Up and Down [ ]/[ ] buttons to select "1. Speaker Config," and then press [ENTER]. The Speaker Config menu appears. 1.Speaker Config a.Subwoofer :Yes b.Front : 100Hz c.Center : 100Hz d.Surround : 100Hz e.LPFofLFE : 120Hz f.DoubleBass :--- Use the Up and Down [ ]/[ ] buttons to select "a. Subwoofer," and then use the Left and Right [ ]/[ ] buttons to select: Yes: Select if a subwoofer is connected. No: Select if no subwoofer is connected. Use the Up and Down [ ]/[ ] buttons to select "b. Front," and then use the Left and Right [ ]/ [ ] buttons to select a crossover frequency. Note: If the Subwoofer setting in step 3 is set to No, this setting is fixed at Full Band. Use the Up and Down [ ]/[ ] buttons to select "c. Center," and then use the Left and Right [ ]/ [ ] buttons to select a crossover frequency. If no center speaker is connected, select None. Note: If the Front setting in step 4 is set to anything other than Full Band, Full Band cannot be selected here. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
42
First Time Setup
—Continued
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
The following crossover frequencies can be speci
fi
ed:
Full Band, 40 Hz, 50 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz,
150 Hz, 200 Hz.
Specify Full Band for speakers that can output low-fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify
a crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speakers
’
manuals to determine
the optimum crossover frequencies
.
Speaker Con
fi
guration
1
Press the [RECEIVER] or [AMP]
button followed by the [SETUP]
button.
The main menu appears onscreen.
MUTING
PREVIOUS
MENU
GUIDE
TOP MENU
SETUP
RETURN
PLAYLIST/CAT
PLAYLIST/CAT
--
/
---
TAPE/AMP
M
D/CDR
HDD
CABLE
STANDBY/ON
DIMMER
ENT
D TUN
SLEEP
10
11
12
INPUT SELECTOR
REMOTE MODE
V
1
V
4
V
2
V
3
C
D
TAPE
TUNER
DVD
MULTI CH
TV
VOL
VOL
SAT
VCR
TV
DVD
RECEIVER
C
D
INPUT
+10
0
CLR
1
2
3
4
5
6
7
8
9
ENTER
CH
DISC
ALBUM
1, 11
2-10
2
1
RECEIVER
AMP
SETUP
2
Use the Up and Down [
]/[
]
buttons to select
“
1. Speaker
Con
fi
g,
”
and then press [ENTER].
The Speaker Con
fi
g menu appears.
3
Use the Up and Down [
]/[
]
buttons to select
“
a. Subwoofer,
”
and then use the Left and Right
[
]/[
] buttons to select:
Yes:
Select if a subwoofer is con-
nected.
No:
Select if no subwoofer is con-
nected.
4
Use the Up and Down [
]/[
]
buttons to select
“
b. Front,
”
and
then use the Left and Right [
]/
[
] buttons to select a crossover
frequency.
Note:
If the Subwoofer setting in step 3 is set
to No, this setting is
fi
xed at Full Band.
5
Use the Up and Down [
]/[
]
buttons to select
“
c. Center,
”
and
then use the Left and Right [
]/
[
] buttons to select a crossover
frequency.
If no center speaker is connected, select
None.
Note:
If the Front setting in step 4 is set to
anything other than Full Band, Full
Band cannot be selected here.
1.Speaker Config
------------------------
a.Subwoofer
:Yes
b.Front
:
100Hz
c.Center
:
100Hz
d.Surround :
100Hz
e.LPFofLFE :
120Hz
f.DoubleBass
:---