Onkyo HT-R640 Owner Manual - Page 48

Listening to the Radio

Get Onkyo HT-R640 PDF manuals and user guides View all Onkyo HT-R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Listening to the Radio Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. Listening to the Radio TUNER Use the [TUNER] input selector button to select either AM or FM. In this example, FM has been selected. Each time you press the [TUNER] but- ton, the input source changes between AM and FM. Band Frequency (Actual display depends on country) Tuning into Radio Stations I Manual Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. 2 TUNING PRESET Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. The North American models change FM frequency in 0.2 MHz steps, 10 kHz steps for AM. For other models it's 0.05 MHz steps for FM and 9 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. 12 I Auto Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. 2 TUNING PRESET Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator appears on the display, as shown. TUNED AUTO I Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. 1 AMP RECEIVER Press the [RECEIVER] or [AMP] button, followed by the [D TUN] button. D TUN 2 (Actual display depends on country.) The [RECEIVER] or [AMP] button flashes. Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87.5 (FM), press 8, 7, 5. Note: While the [RECEIVER] or [AMP] button is flashing, the input source cannot be changed by using the remote controller. FM STEREO 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
48
Listening to the Radio
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
Listening to the Radio
Tuning into Radio Stations
■
Auto Tuning Mode
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator appears on the display, as shown.
■
Manual Tuning Mode
The North American models change FM frequency in
0.2 MHz steps, 10 kHz steps for AM. For other models
it
’
s 0.05 MHz steps for FM and 9 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
■
Tuning into Stations by Frequency
You can tune into AM and FM stations directly by enter-
ing the appropriate frequency.
Using the Tuner
Use the [TUNER] input selector
button to select either AM or FM.
In this example, FM has been selected.
Each time you press the [TUNER] but-
ton, the input source changes between
AM and FM.
(Actual display depends on country)
1
Press the [TUNING MODE] button
so that the AUTO indicator
appears on the display.
2
Press the TUNING Up or Down
[
]/[
] button.
Searching stops when a station is
found.
TUNER
Band
Frequency
2
1
TUNING
MODE
TUNING
PRESET
AUTO
TUNED
FM STEREO
1
Press the [TUNING MODE] button
so that the AUTO indicator disap-
pears from the display.
2
Press and hold the TUNING Up or
Down [
]/[
] button.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
1
Press the [RECEIVER] or [AMP]
button, followed by the [D TUN]
button.
(Actual display depends on country.)
The [RECEIVER] or [AMP] button
fl
ashes.
2
Within 8 seconds, use the num-
ber buttons to enter the fre-
quency of the radio station.
For example, to tune to 87.5 (FM),
press 8, 7, 5.
Note
: While the [RECEIVER] or
[AMP] button is
fl
ashing, the input
source cannot be changed by using the
remote controller.
TUNING
MODE
TUNING
PRESET
D TUN
RECEIVER
AMP