Sony RM-AX4000 Operating Instructions - Page 73

73

Additional Information

Problem

Even if you operate an

XPRESS function, the

Source component does

not turn on, or it turns off.

Even if you operate an

XPRESS function, the input

selector of the TV or RCVR

(Receiver/Amplifier) does

not achieve the correct

status.

Air-Slide does not work

properly.

Trouble with setting mode

Solution

•

The Remote Commander memorizes the status of the

component's input selector and power on/off. However, if you

turn on/off the component with the remote control or operate the

component directly, it will not recognize the current component

status. In this case, press SYNC-UP button to synchronize the

status of the current component and the Remote Commander.

•

If the TV turns off by its own Sleep function, the Remote

Commander does not recognize its status. Turn off the TV with

the Remote Commander. You can also turn off the TV at the

scheduled time with the Timer on the Remote Commander.

•

The Remote Commander memorizes the status of the

component's input selector and power on/off. However, if you

turn on/off the component with the remote control or operate the

component directly, it will not recognize the current component

status. In this case, press the SYNC-UP button to synchronize the

status of the current component and the Remote Commander.

•

If the TV turns off by its own Sleep function, the Remote

Commander does not recognize its status. Turn off the TV with

the Remote Commander. You can also turn off the TV at the

scheduled time with the Timer on the Remote Commander.

Make sure to slide your finger from the top-left on the LCD display.

If you slide other than from the top-left, Air-Slide cannot recognize

the action.

Continued

Problem

You cannot operate the

component even after you

programmed a preset code.

You cannot operate a

component even after you

programmed remote

control signals with the

“learning” function.

“NG” flashes 5 times when

learning.

Solution

• Set the preset code correctly. If the preset code that is listed first

for your component does not work, try all the preset codes for

your component in the order listed in the supplied “Preset Code

Lists.”

• Some features may not be preset. If some or all of the keys do not

function correctly even after you have set the preset codes, use the

learning function to program the remote control signals for the

component (page 47).

• If you set a component code after changing the label of a

component, they are cleared and return to the original label.

Change the label of a component after you decide the component

to be used by presetting a code.

Make sure that the Remote Commander has learned the correct

signals. See “For accurate learning” (page 51) and try the learning

procedure again (page 48).

• Leaning has not succeeded. After checking the following, try the

learning procedure again (page 48).

–

Change the distance between the Remote Commander and

remote control.

–

See “For accurate learning” (page 51).

• The preset codes cannot be set. See the supplied “Preset Code

Lists” and try setting the preset codes again (page 45).

Section	Page
WARNING	2
Features	4
Table of Contents	6
Getting Started	8
Unpacking	8
Location and function of controls	8
Installing the batteries	10
When to replace the batteries	10
Setting the clock	11
Remote Commander settings and operating procedures	13
About the factory setting	13
How to set up the Remote Commander (On-PC Setup and On-Remote Setup)	13
Setting procedure for On-PC Setup	14
Setting procedure for On-Remote Setup	15
Setting up for your PC	16
Installing the “AX Remote Editor”	16
Installing the USB driver	17
Connecting the Remote Commander to your PC	19
Using the “AX Remote Editor” to set up the Remote Commander	19
Using “AX Remote Editor” - Help	20
Operating	21
Operating the Remote Commander	21
What is the XPRESS function?	21
Operating the XPRESS function	22
Operating components individually	25
To control the volume	27
To synchronize with the status of a component - SYNC-UP	28
To perform an easy action “Air-Slide” for XPRESS function	29
Executing a series of actions at a scheduled time - Timer function	29
To quickly switch the Timer on or off	30
Executing a series of commands with just one button - System Control function	31
Other useful functions	32
To operate the Remote Commander in the dark	32
Locking the controls - Hold function	33
To turn off all the components at one time	33
Unit Settings	34
Setting the backlight	34
Setting the LCD display	37
Setting the automatic-off time of the LCD display	37
Calibrating the alignment of the LCD display	39
Setting the contrast of the LCD display	40
Setting the beep	41
Adjusting the clock	42
To change the display to the daylight savings time (summer time) indication	43
Setting by On-Remote Setup	45
Setting the preset codes	45
Using non-preset remote control operations - Learning function	47
To clear the learned signal from a key or button	49
Learning up to 4 signals to one key	49
For accurate learning	51
Programming a series of actions with just one button -System Control function	51
To clear programmed series of actions for SYSTEM CONTROL button or System Control key	54
Setting the XPRESS macro activation	56
Controlling the volume of visual components connected to an audio component	57
Setting the Timer	59
To program the Timer	59
To clear a Timer macro	64
Changing the names of labels	65
Erasing all the settings - Reset	68
Additional Information	70
Precautions	70
Maintenance	70
Specifications	70
Troubleshooting	71
Appendix	76
Table of preset functions	76
TV	76
A-CBL (Analog Cable box)	77
D-SAT (Digital Satellite)	78
DVD (DVD player)	79
VCR (Video Cassette Recorder)	80
DVR (Digital Video Recorder) - DVR, PVR, DVR/Satellite Combo, DVR/Cable Combo	81
CD (CD player)	82
RCVR (Receiver/Amplifier)	83
DVDVR (DVR/DVD combo)	84
DVD-R (DVD Recorder)	85
D-CBL (Digital Cable box)	86
DAV (DVD/Receiver combo)	87
PJ (Projector)	88
TAPE (Cassette deck)	89
MD (MD deck)	90
LIGHT	91
Full Display	92

Sony RM-AX4000 Operating Instructions - Page 73

Trouble with setting mode, Additional Information

Page 73 highlights