Toshiba 52HM95 Owner's Manual - English - Page 43

To remove a channel from the channel memory

Get Toshiba 52HM95 - 52inch Rear Projection TV PDF manuals and user guides
UPC - 022265251157
View all Toshiba 52HM95 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Chapter 6: Setting up your TV Programming channels into the TV's channel memory (continued) Manually adding and deleting channels in the channel memory After automatically programming channels into the channel memory, you can manually add or delete individual channels. To add or delete channels in the channel memory: 1. Press MENU and open the Setup menu. 2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3). Setup Installation Sleep Timer On/Off Timer HDMI 1 Audio HDMI 2 Audio Slide Show Interval AVHD Skip Time Auto Auto 2 Sec 15 min Navigate Select CH RTN Back EXIT Exit 3. Open the Terrestrial menu, highlight Channel Add/Delete, and then press ENTER. Terrestrial Input Configuration Channel Program Channel Add/Delete Signal Meter Navigate Select CH RTN Back EXIT Exit 4. The illustration below left shows channels programmed for the ANT 1 antenna input. To view the list of channels programmed for the Cable box or ANT 2 antenna input, press the y z buttons to highlight either "ANT 2" or "Cable Box" and press ENTER. Note: "Cable Box" will appear only if you connected a cable box to your TV. Channel Add/Delete 2 2 - 1 2 - 2 3 4 5 6 7 7 - 1 8 Analog Digital Digital Analog Analog Analog Analog Analog Digital Analog ANT 1 ANT 1 ANT 2 Cable Box Reset Cancel Done Channel Add/Delete 1 2 3 4 5 6 7 8 9 10 Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog ANT 2 ANT 1 ANT 2 Cable Box Reset Cancel Done To add a channel to the channel memory: Highlight the unchecked box next to the channel number you want to add, and then press ENTER to check the box. To manually add digital subchannels on a physical channel: Use the Channel Numbers and the Dash (-/100) on the remote control to enter the channel number (for example, 56-1). If the channel is found, the number will be added to the list and the box will be checked. If the channel is not found, a message will appear. To remove a channel from the channel memory: Highlight the checked box next to the channel number you want to remove, and then press ENTER to uncheck the box. To save your new settings: Highlight Done and press ENTER. To revert to your original settings: Highlight Cancel and press ENTER before saving. To remove all channels from the channel memory: Highlight Reset and press ENTER, and then highlight Done and press ENTER. Note: • This action applies to the current antenna input only. To delete/add channels on the other input, highlight the input you want (ANT1 or ANT 2) and press ENTER. • This action cannot be cancelled unless you highlight Cancel and press ENTER before saving your changes. Channel Add/Delete 2 2 - 1 2 - 2 3 4 5 6 7 7 - 1 8 Analog Digital Digital Analog Analog Digital Analog Analog Digital Analog ANT 1 ANT 1 ANT 2 Cable Box Reset Cancel Done HM95_R1_041-43_061505 43 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 6/24/05, 9:40 PM 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
43
(E) 46/52/62HM95
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
Chapter 6: Setting up your TV
Manually adding and deleting channels in
the channel memory
After automatically programming channels into the channel
memory, you can manually add or delete individual channels.
To add or delete channels in the channel memory:
1.
Press MENU and open the Setup menu.
2.
Highlight Installation and press ENTER. (A new set of
Installation menu icons will appear on-screen, as shown in
step 3).
Navigate
Select
Back
Exit
CH RTN
EXIT
Installation
Sleep Timer
On/Off Timer
HDMI 1 Audio
Auto
Auto
2 Sec
15 min
HDMI 2 Audio
Slide Show Interval
AVHD Skip Time
Setup
3.
Open the Terrestrial menu, highlight Channel Add/Delete,
and then press ENTER.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate
Select
Back
Exit
CH RTN
EXIT
4.
The illustration below left shows channels programmed for
the ANT 1 antenna input. To view the list of channels
programmed for the Cable box or ANT 2 antenna input,
press the
y
z
buttons to highlight either “ANT 2” or
“Cable Box” and press ENTER.
Note:
“Cable Box” will appear only if you connected a cable
box to your TV.
Channel Add/Delete
2
Analog
ANT 1
Cable Box
ANT 2
ANT 1
Reset
Cancel
Done
Digital
Digital
Analog
Analog
Analog
Analog
Analog
Digital
Analog
2 - 1
2 - 2
3
4
5
6
7
7 - 1
8
Channel Add/Delete
1
Analog
ANT 1
ANT 2
ANT 2
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
2
3
4
5
6
7
8
9
10
Cable Box
Reset
Cancel
Done
Programming channels into the TV’s channel memory
(continued)
To add a channel to the channel memory:
Highlight the unchecked box next to the channel number
you want to add, and then press ENTER to check the box.
To manually add digital subchannels on a physical channel:
Use the Channel Numbers and the Dash (–/100) on the
remote control to enter the channel number (for example,
56–1).
If the channel is found, the number will be added to the list
and the box will be checked.
If the channel is not found, a message will appear.
To remove a channel from the channel memory:
Highlight the checked box next to the channel number you
want to remove, and then press ENTER to uncheck the
box.
To save your new settings:
Highlight Done and press ENTER.
To revert to your original settings:
Highlight Cancel and press ENTER before saving.
To remove all channels from the channel memory:
Highlight Reset and press ENTER, and then highlight
Done and press ENTER.
Note:
•
This action applies to the current antenna input only. To
delete/add channels on the other input, highlight the input
you want (ANT1 or ANT 2) and press ENTER.
•
This action cannot be cancelled unless you highlight Cancel
and press ENTER before saving your changes.
Channel Add/Delete
2
Analog
ANT 1
ANT 2
ANT 1
Reset
Cancel
Done
Digital
Digital
Analog
Analog
Digital
Analog
Analog
Digital
Analog
2 - 1
2 - 2
3
4
5
6
7
7 - 1
8
Cable Box
HM95_R1_041-43_061505
6/24/05, 9:40 PM
43