Behringer DEEPMIND 12 Manual - Page 111

NoiseGate NOISE GATE, Delay STEREO DELAY

Get Behringer DEEPMIND 12 PDF manuals and user guides View all Behringer DEEPMIND 12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

111 DeepMind 12 User Manual NoiseGate (NOISE GATE) No DM12 REF PARAMETER UNITS MIN MAX DESCRIPTION 1* THR Threshold dB -50.0 0.0 Sets signal level at which gate opens. 2* RNG Range dB -100.0 0.0 Control adjusts the amount of gain reduction applied to the signal below threshold. 3* ATT Attack ms 0.0 20.0 Adjusts time taken for gate to open after an over-threshold signal. 4* REL Release ms 2.0 1999.9 Adjusts time taken for gate to close after programme material falls back below threshold. 5* HLD Hold ms 2.0 1999.9 This defines a waiting period before the gate starts to close. 6* PUN Punch - -6.0 6.0 Used to increase tonal shaping or reduce gated breathing/delay/resonant howl-round. 7 MOD Mode -- - GAT (Gate), TRN (Transient Gate), DUC (Ducker). 8 PWR Power - ON OFF Enables gate in the signal path. When switched off, gate is bypassed. * These parameters are available as modulation destinations in the Modulation Matrix Delay (STEREO DELAY) No DM12 REF PARAMETER UNITS MIN MAX DESCRIPTION 1* MIX Mix % 0.0% 100% Controls the mix (or ratio) of wet (processed) and dry (unprocessed) signals. 2 TIM Time ms 1.0 ms 1500.0 ms Adjusts the master delay time. Time synchronised options from 4 to 1/64 bars. 3 MOD Mode -- - ST- Stereo feedback, X - crosses feedback between channels, M - Mono mix in feedback chain. P-P - Ping Pong (Note that Feedback-R (FBR) is disabled in this mode. 4 FCL FactorL -- - Sets left delay to rhythmic fractions of the master delay (1/4, 3/8, 1/2, 2/3, 1, 4/3, 3/2, 2, 3). 5 FCR FactorR -- - Sets right delay to rhythmic fractions of the master delay (1/4, 3/8, 1/2, 2/3, 1, 4/3, 3/2, 2, 3). 6 OFS Offset ms -100.0 ms 100.0 ms Adds a delay difference between the left and right delayed signals. 7* LC LC Hz 10.0 Hz 500.0 Hz Adjusts the low frequency cut, allowing lower frequencies to remain unaffected by the delay. 8* HC HC Hz 200.0 Hz 20000.0 Hz Adjusts the high frequency cut, allowing higher frequencies to remain unaffected by the delay. 9* FLC FeedLC Hz 10.0 Hz 500.0 Hz Adjusts the low cut filter frequency in the feedback paths. 10* FBL FeedL % 0.0% 100% Control the amount of feedback for the left channel. 11* FBR FeedR % 0.0% 100% Control the amount of feedback for the right channel. 12* FHC FeedHC Hz 200.0 Hz 20000.0 Hz Adjusts the high cut filter frequency in the feedback paths. * These parameters are available as modulation destinations in the Modulation Matrix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
111
DeepMind 12 User Manual
NoiseGate (NOISE GATE)
No
DM12 REF
PARAMETER
UNITS
MIN
MAX
DESCRIPTION
1*
THR
Threshold
dB
-50.0
0.0
Sets signal level at which gate opens.
2*
RNG
Range
dB
-100.0
0.0
Control adjusts the amount of gain reduction applied to the signal below threshold.
3*
ATT
Attack
ms
0.0
20.0
Adjusts time taken for gate to open after an over-threshold signal.
4*
REL
Release
ms
2.0
1999.9
Adjusts time taken for gate to close after programme material falls back below threshold.
5*
HLD
Hold
ms
2.0
1999.9
This defines a waiting period before the gate starts to close.
6*
PUN
Punch
—
-6.0
6.0
Used to increase tonal shaping or reduce gated breathing/delay/resonant howl-round.
7
MOD
Mode
—
—
—
GAT (Gate), TRN (Transient Gate), DUC (Ducker).
8
PWR
Power
—
ON
OFF
Enables gate in the signal path. When switched off, gate is bypassed.
* These parameters are available as modulation destinations in the Modulation Matrix
Delay (STEREO DELAY)
No
DM12 REF
PARAMETER
UNITS
MIN
MAX
DESCRIPTION
1*
MIX
Mix
%
0.0%
100%
Controls the mix (or ratio) of wet (processed) and dry (unprocessed) signals.
2
TIM
Time
ms
1.0 ms
1500.0 ms
Adjusts the master delay time. Time synchronised options from 4 to 1/64 bars.
3
MOD
Mode
—
—
—
ST- Stereo feedback, X - crosses feedback between channels, M - Mono mix in feedback chain.
P-P - Ping Pong (Note that Feedback-R (FBR) is disabled in this mode.
4
FCL
FactorL
—
—
—
Sets left delay to rhythmic fractions of the master delay (¸² ³´µ² °² ½´·, 1, ¾´·² ³´», 2, 3).
5
FCR
FactorR
—
—
—
Sets right delay to rhythmic fractions of the master delay (¸² ³´µ² °² ½´·, 1, ¾´·² ³´», 2, 3).
6
OFS
Offset
ms
-100.0 ms
100.0 ms
Adds a delay difference between the left and right delayed signals.
7*
LC
LC
Hz
10.0 Hz
500.0 Hz
Adjusts the low frequency cut, allowing lower frequencies to remain unaffected by the delay.
8*
HC
HC
Hz
200.0 Hz
20000.0 Hz
Adjusts the high frequency cut, allowing higher frequencies to remain unaffected by the delay.
9*
FLC
FeedLC
Hz
10.0 Hz
500.0 Hz
Adjusts the low cut filter frequency in the feedback paths.
10*
FBL
FeedL
%
0.0%
100%
Control the amount of feedback for the left channel.
11*
FBR
FeedR
%
0.0%
100%
Control the amount of feedback for the right channel.
12*
FHC
FeedHC
Hz
200.0 Hz
20000.0 Hz
Adjusts the high cut filter frequency in the feedback paths.
* These parameters are available as modulation destinations in the Modulation Matrix