Campbell Scientific CSAT3B CSAT3B Three-Dimensional Sonic Anemometer - Page 33

TABLE 7-1., CSAT3B Settings and Status Values in, Subscreen, Setting or Status, Value, Options,

Get Campbell Scientific CSAT3B PDF manuals and user guides View all Campbell Scientific CSAT3B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

CSAT3B Three-Dimensional Sonic Anemometer describes each of the settings or status values in these subscreens. For each setting or status value, the factory default setting is noted by the footnote. Ensure that the appropriate settings are enabled for the communication protocol that will be used. An example subscreen is shown in FIGURE 7-2. TABLE 7-1. CSAT3B Settings and Status Values in Device Configuration Utility Subscreen Setting or Status Value Options Anemometer Data - Real-Time Data Communication Settings Internal Temperature - Internal Relative Humidity - Inclinometer Pitch - Inclinometer Roll - SDM Address CPI Address Communication Port Protocol CPI Baud Rate RS-485 Baud Rate Unprompted Output Port 1 through 14 31 1 through 120 301 Disable Both CPI Enabled1 RS-485 Enabled Auto1 1000 kbps 500 kbps 250 kbps 125 kbps 50 kbps 1200 2400 4800 9600 19200 38400 57600 1152001 230400 Disabled1 USB Port RS-485 Port Description Shows real-time measurements of Ux, Uy, Uz, sonic temperature (Ts), and the diagnostic word. If in operating Mode 1 (see Section 8.2, Operating Mode), values will flash each second. Temperature inside CSAT3B block Relative humidity inside CSAT3B block. Change desiccant if greater than 50% (see Section 9.3, Desiccant). Pitch angle of CSAT3B head (see Section 7.3, Mounting) Roll angle of CSAT3B head (see Section 7.3, Mounting) Unique address for SDM device Unique address for CPI device Identifies whether the RS-485/CPI port will be disabled, enabled for CPI, or enabled for RS-485 Baud rate for CPI communications (in most circumstances this setting should remain set to Auto) Baud rate for RS-485 communications Identifies the port to output unprompted data 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
CSAT3B Three-Dimensional Sonic Anemometer
describes each of the settings or status values in these subscreens.
For
each setting or status value, the factory default setting is noted by the
footnote.
Ensure that the appropriate settings are enabled for the
communication protocol that will be used.
An example subscreen is
shown in FIGURE 7-2.
TABLE 7-1.
CSAT3B Settings and Status Values in
Device Configuration Utility
Subscreen
Setting or Status
Value
Options
Description
Real-Time Data
Anemometer Data
-
Shows real-time measurements of U
x
, U
y
,
U
z
, sonic temperature (T
s
), and the
diagnostic word.
If in operating Mode 1
(see Section 8.2,
Operating Mode
), values
will flash each second.
Internal
Temperature
-
Temperature inside CSAT3B block
Internal Relative
Humidity
-
Relative humidity inside CSAT3B block.
Change desiccant if greater than 50% (see
Section 9.3,
Desiccant
).
Inclinometer
Pitch
-
Pitch angle of CSAT3B head (see Section
7.3,
Mounting
)
Inclinometer Roll
-
Roll angle of CSAT3B head (see Section
7.3,
Mounting
)
Communication
Settings
SDM Address
1 through 14
3
1
Unique address for SDM device
CPI Address
1 through 120
30
1
Unique address for CPI device
Communication
Port Protocol
Disable Both
CPI Enabled
1
RS-485 Enabled
Identifies whether the RS-485/CPI port will
be disabled, enabled for CPI, or enabled for
RS-485
CPI Baud Rate
Auto
1
1000 kbps
500 kbps
250 kbps
125 kbps
50 kbps
Baud rate for CPI communications
(in most circumstances this setting should
remain set to
Auto
)
RS-485 Baud
Rate
1200
2400
4800
9600
19200
38400
57600
115200
1
230400
Baud rate for RS-485 communications
Unprompted
Output Port
Disabled
1
USB Port
RS-485 Port
Identifies the port to output unprompted
data
23