Campbell Scientific CSAT3B CSAT3B Three-Dimensional Sonic Anemometer - Page 55

Operating Modes

Get Campbell Scientific CSAT3B PDF manuals and user guides View all Campbell Scientific CSAT3B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

CSAT3B Three-Dimensional Sonic Anemometer 8.2 Operating Modes The CSAT3B has different operating modes that are selected based on the desired measurement trigger source, presence of a data filter, and type of data output. Specifically, the following four modes are available: • Mode 1: Datalogger-triggered | No filter | Datalogger-prompted output • Mode 2: Self-triggered | Filtered | Datalogger-prompted output • Mode 3: Self-triggered | No filter | Unprompted output to PC • Mode 4: Self-triggered | Filtered | Unprompted output to PC The mode is selected using the Device Configuration Utility under the Measurement Settings tab (see Section 7.1, Settings, for details on viewing and selecting settings). TABLE 8-1 gives a summary of the CSAT3B operating modes. The following sections give more information on the measurement trigger, data filters, and data output as a guide to selecting the appropriate mode. Mode 1 is the default operating mode for the CSAT3B and is recommended when fluxes are the primary interest. FIGURE 8-1. Measurement settings in Device Configuration Utility 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
CSAT3B Three-Dimensional Sonic Anemometer
8.2
Operating Modes
The CSAT3B has different operating modes that are selected based on the
desired measurement trigger source, presence of a data filter, and type of data
output.
Specifically, the following four modes are available:
•
Mode 1:
Datalogger-triggered | No filter | Datalogger-prompted output
•
Mode 2:
Self-triggered | Filtered | Datalogger-prompted output
•
Mode 3:
Self-triggered | No filter | Unprompted output to PC
•
Mode 4:
Self-triggered | Filtered | Unprompted output to PC
The mode is selected using the
Device Configuration Utility
under the
Measurement Settings
tab (see Section 7.1,
Settings,
for details on viewing and
selecting settings).
TABLE 8-1 gives a summary of the CSAT3B operating
modes.
The following sections give more information on the measurement
trigger, data filters, and data output as a guide to selecting the appropriate
mode. Mode 1 is the default operating mode for the CSAT3B and is
recommended when fluxes are the primary interest.
FIGURE 8-1.
Measurement settings in Device Configuration Utility
45