Casio WK 3500 User Guide - Page 134
Compressor, Limiter, Distortion, Stereo Phaser, Phaser
UPC - 079767312756
View all Casio WK 3500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 134 highlights
04.3.26, 0:12 PM 20 WK3000_e_A-19-31.p65 735A-E-134A A-20 3 : Depth(Range: -64 to 0 to +63) Adjusts the depth of the wah in accordance with the level of the input signal. Setting a positive value causes the wah filter to open in direct proportion with the size of the input signal, producing a bright sound. Setting a negative value causes the Wah filter to close in accordance with the size of the input signal, which produces a dark tone quality. However, large input re-opens the Wah filter, even if it is closed. 06 : Compressor I Function Compresses the input signal, which can have the effect of suppressing level variation and making it possible to sustain dampened sounds longer. I Parameters 0 : Depth (Range: 0 to 127) Adjusts compression of the audio signal. 1 : Attack (Range: 0 to 127) Adjusts the attack amount of the input signal. A smaller value causes prompt compressor operation, which suppresses the attack of the input signal. A larger values delays compressor operation, which causes attack to be output as-is. 2 : Release (Range: 0 to 127) Adjusts the time from the point when the input signal drops below a certain level until the compression operation is stopped. When an attack feeling is desired (no compression at the onset of the sound), set this parameter to as low a value as possible. To have compression applied at all times, set a high value. 3 : Level (Range: 0 to 127) Adjusts the output level. The output volume changes in accordance with the Depth setting and the characteristics of the input tone. Use this parameter to correct for such changes. 07 : Limiter I Function This is an effector that you can use to set an upper limit value on the level of the input signal. I Parameters 0 : Limit (Range: 0 to 127) Adjusts the volume level from which the limit is applied. 1 : Attack (Range: 0 to 127) Adjusts the attack amount of the input signal. 2 : Release (Range: 0 to 127) Adjusts the time from when the input signal drops below a certain level until the limit operation stops. 3 : Level (Range: 0 to 127) Adjusts the level being output. The output volume changes in accordance with the Limit setting and the characteristics of the input tone. Use this parameter to correct for such changes. 08 : Distortion I Function This effect provides Distortion + AmpSimulator. I Parameters 0 : Gain (Range: 0 to 127) Adjusts the input gain. 1 : Low (Range: 0 to 127) Adjusts the low-band gain. The cutoff frequency differs according to the preset DSP. 2 : High (Range: 0 to 127) Adjusts the high-band gain. The cutoff frequency differs according to the preset DSP. 3 : Level (Range: 0 to 127) Adjusts the output level. 09 : Stereo Phaser I Function This is a stereo phaser that modulates the phase in accordance with a sine wave LFO. I Parameters 0 : Resonance (Range: 0 to 127) Adjusts the resonance of the sound. 1 : Manual (Range: -64 to 0 to +63) Adjusts the phaser shift volume, which is used for reference. 2 : Rate (Range: 0 to 127) Adjusts the rate of the LFO. 3 : Depth (Range: 0 to 127) Adjusts the depth of the LFO. 4 : Wet Level (Range: 0 to 127) Adjusts the volume level of the effect. 10 : Phaser I Function This is a monaural phaser that modulates the phase in accordance with a sine wave LFO. I Parameters 0 : Resonance (Range: 0 to 127) Adjusts the resonance of the sound. 1 : Manual (Range: -64 to 0 to +63) Adjusts the phaser shift volume, which is used for reference. Appendix