D-Link DSL-504T Product Manual - Page 19

Power On Router - default password

Get D-Link DSL-504T PDF manuals and user guides
UPC - 790069265204
View all D-Link DSL-504T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

DSL-504T User's Manual Power On Router Power On Router CAUTION: The Router must be used with the power adapter included with the device. To power on the Router: 1. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router and plug the adapter into a suitable nearby power source. 2. You should see the Power LED indicator light up and remain lit. The Status LED should light solid green and begin to blink after a few seconds. 3. If the Ethernet port is connected to a working device, check the Ethernet Link/Act LED indicators to make sure the connection is valid. The Router will attempt to establish the ADSL connection, if the ADSL line is connected and the Router is properly configured this should light up after several seconds. If this is the first time installing the device, some settings may need to be changed before the Router can establish a connection. Factory Reset Button The Router may be reset to the original factory default settings by depressing the reset button for at least seven seconds while the device is powered on. Use a ballpoint or paperclip to gently push down the reset button. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings. The device settings will be restored to the factory default IP address 192.168.1.1 and the subnet mask is 255.255.255.0, the default management Username is admin and the default Password is admin. D-Link Systems, Inc. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
19
DSL-504T User’s Manual
D-Link Systems, Inc.
Power On Router
Power On Router
CAUTION:
The Router must be used with the power adapter included
with the device.
To power on the Router:
1.
Insert the AC Power Adapter cord into the power receptacle located on the rear
panel of the Router and plug the adapter into a suitable nearby power source.
2.
You should see the Power LED indicator light up and remain lit. The Status LED
should light solid green and begin to blink after a few seconds.
3.
If the Ethernet port is connected to a working device, check the Ethernet Link/Act
LED indicators to make sure the connection is valid. The Router will attempt to
establish the ADSL connection, if the ADSL line is connected and the Router is
properly configured this should light up after several seconds. If this is the first
time installing the device, some settings may need to be changed before the
Router can establish a connection.
Factory Reset Button
The Router may be reset to the original factory default settings by depressing
the reset button for at least seven seconds while the device is powered on. Use a
ballpoint or paperclip to gently push down the reset button. Remember that this will
wipe out any settings stored in flash memory including user account information and
LAN IP settings. The device settings will be restored to the factory default IP address
192.168.1.1 and the subnet mask is 255.255.255.0, the default management
Username is
admin
and the default Password is
admin
.