D-Link DSL-504T Product Manual - Page 48

Dynamic IP Address for WAN continued - default ip address

Get D-Link DSL-504T PDF manuals and user guides
UPC - 790069265204
View all D-Link DSL-504T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

DSL-504T User's Manual Configuring the WAN Connection Dynamic IP Address for WAN (continued) ATM VC Settings: The ATM VC Settings at the top of the menu should not be changed unless you have been instructed to change them. However, if you are instructed to change the VPI or VCI values, type in the values assigned for your account Leave the PVC and Virtual Circuit settings at their default (Pcv0 and Enabled) values for now. These can be used later if you are configuring multiple virtual circuits for your ADSL service. WAN Settings: Dynamic IP Address is selected. Dynamic IP- Under Dynamic IP section, choose the Connection Type from the Connection Type: pull-down menu. For Dynamic IP mode connections the available encapsulation methods are 1483 Bridged IP LLC and 1483 Bridged IP VCMux. Dynamic IPCloned MAC Address Some ISP's may require you to use the original computer that was originally registered for the Internet service. In this case, type in the MAC address of the computer that was used. To obtain the MAC address of the computer, you can do the following: For Windows Start>Run>cmd>OK XP/2000: In the command prompt, type in ipconfig/all. The physical address is the MAC address of the computer. For Windows Me: Start >Run >command >OK In the command prompt, type in ipconfig/all. The physical address is the MAC address of the computer. D-Link Systems, Inc. ATM: If you have not been instructed to change the ATM settings at the bottom of the menu, leave these at the default settings. If you have been given new settings to configure, select the Service Category and type in the values for PCR and VCI in Kbps. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
48
DSL-504T User’s Manual
D-Link Systems, Inc.
ATM VC Settings:
WAN Settings:
Dynamic IP-
Connection Type:
Dynamic IP-
Cloned MAC Address
The
ATM VC Settings
at the top of the menu should not be changed
unless you have been instructed to change them. However, if you
are instructed to change the
VPI
or
VCI
values, type in the values
assigned for your account Leave the
PVC
and
Virtual Circuit
settings at their default (
Pcv0
and
Enabled
) values for now. These
can be used later if you are configuring multiple virtual circuits for
your ADSL service.
Dynamic IP Address is selected.
Under
Dynamic IP section
, choose the
Connection Type
from the
pull-down menu. For Dynamic IP mode connections the available
encapsulation methods are
1483 Bridged IP LLC
and
1483 Bridged
IP VCMux
.
Some ISP’s may require you to use the original computer that was
originally registered for the Internet service. In this case, type in the
MAC address of the computer that was used. To obtain the MAC
address of the computer, you can do the following:
Configuring the WAN Connection
Dynamic IP Address for WAN (continued)
Start
>
Run
>
cmd
>
OK
In the command prompt, type in
ipconfig/all
. The physical address
is the MAC address of the computer.
For Windows
XP/2000:
Start
>
Run
>
command
>
OK
In the command prompt, type in
ipconfig/all
. The physical address
is the MAC address of the computer.
For Windows Me:
If you have not been instructed to change the ATM settings at the
bottom of the menu, leave these at the default settings. If you have
been given new settings to configure, select the
Service Category
and type in the values for
PCR
and
VCI
in Kbps.
ATM: