Dell PowerEdge C6420 EMC Installation and Service Manual - Page 103

Removing the M.2 SATA card

Get Dell PowerEdge C6420 PDF manuals and user guides View all Dell PowerEdge C6420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Figure 54. Installing the M.2 SATA x16 riser Next steps 1. Follow the procedure listed in After working inside your system. Removing the M.2 SATA card Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If applicable, remove the expansion card riser assembly. 4. Remove the M.2 x16 riser or install the M.2 SATA x8 mezzanine card. NOTE: The procedure to remove the M.2 SATA x8 mezzanine card is similar to removing a mezzanine card. Steps 1. Using the Phillips #1 screwdriver, unscrew the screw that secures the M.2 card to the board. 2. Pull the card out of the connector and lift the card away. Installing and removing enclosure components 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Figure 54. Installing the M.2 SATA x16 riser
Next steps
1.
Follow the procedure listed in
After working inside your system
.
Removing the M.2 SATA card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If applicable,
remove the expansion card riser assembly
.
4.
Remove the M.2 x16 riser
or
install the M.2 SATA x8 mezzanine card
.
NOTE:
The procedure to remove the M.2 SATA x8 mezzanine card is similar to removing a mezzanine card.
Steps
1.
Using the Phillips #1 screwdriver, unscrew the screw that secures the M.2 card to the board.
2.
Pull the card out of the connector and lift the card away.
Installing and removing enclosure components
103