Dell PowerEdge C6420 EMC Installation and Service Manual - Page 98

Installing an expansion card

Get Dell PowerEdge C6420 PDF manuals and user guides View all Dell PowerEdge C6420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Figure 48. Installing the expansion card filler bracket Next steps Install the expansion card or install the expansion card filler bracket. Installing an expansion card Prerequisites CAUTION: Expansion cards can only be installed in the slots on the expansion card riser. Do not attempt to install expansion cards directly into the riser connector on the system board. 1. Follow the safety guidelines listed in Safety instructions. 2. Unpack the expansion card and prepare it for installation. For instructions, see the documentation accompanying the card. Steps 1. If installed, remove the filler bracket by performing the following steps: a. Remove the screw that secures the filler bracket. b. Hold the filler bracket by its edges, and carefully remove it from the riser card. NOTE: You must install an expansion card filler bracket over an empty expansion slot to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. 2. Holding the card by its edges, position the card so that the card edge connector aligns with the connector on the riser card. 3. Insert the card edge connector and push the card firmly into the riser card until the card is fully seated. 4. Replace the screw that secures the expansion card. 98 Installing and removing enclosure components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Figure 48. Installing the expansion card filler bracket
Next steps
Install the expansion card
or
install the expansion card filler bracket
.
Installing an expansion card
Prerequisites
CAUTION:
Expansion cards can only be installed in the slots on the expansion card riser. Do not attempt to install
expansion cards directly into the riser connector on the system board.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Unpack the expansion card and prepare it for installation. For instructions, see the documentation accompanying the card.
Steps
1.
If installed, remove the filler bracket by performing the following steps:
a.
Remove the screw that secures the filler bracket.
b.
Hold the filler bracket by its edges, and carefully remove it from the riser card.
NOTE:
You must install an expansion card filler bracket over an empty expansion slot to maintain Federal
Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the
system and aid in proper cooling and airflow inside the system.
2.
Holding the card by its edges, position the card so that the card edge connector aligns with the connector on the riser card.
3.
Insert the card edge connector and push the card firmly into the riser card until the card is fully seated.
4.
Replace the screw that secures the expansion card.
98
Installing and removing enclosure components