Home » Dell Manuals » Servers » Dell PowerEdge C6420 » Manual Viewer

Dell PowerEdge C6420 EMC Installation and Service Manual - Page 34

Particulate and gaseous contamination specifications, Maximum vibration specifications, Maximum

View all Dell PowerEdge C6420 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Particulate and gaseous contamination specifications Table 24. Particulate contamination specifications Particulate contamination Specifications Air filtration Data center air filtration as defined by ISO Class 8 per ISO 14644-1 with a 95% upper confidence limit. NOTE: This condition applies only to data center environments. Air filtration requirements do not apply to IT equipment designed to be used outside a data center, in environments such as an office or factory floor. NOTE: Air entering the data center must have MERV11 or MERV13 filtration. Conductive dust Air must be free of conductive dust, zinc whiskers, or other conductive particles. NOTE: This condition applies to data center and non-data center environments. Corrosive dust Air must be free of corrosive dust. Residual dust present in the air must have a deliquescent point less than 60% relative humidity. NOTE: This condition applies to data center and non-data center environments. Table 25. Gaseous contamination specifications Gaseous contamination Copper coupon corrosion rate Specifications

Section	Page
Dell EMC PowerEdge C6420 Installation and Service Manual	3
Dell EMC PowerEdge C6420 overview	7
Supported configurations	7
Back view of the PowerEdge C6420 sled	8
Network ports indicator codes	10
Sled to hard drive mapping	11
Expander zoning	11
Locating the Service Tag of your system	13
System information label	14
Documentation resources	17
Technical specifications	19
Dimensions of the Dell EMC PowerEdge C6420 sled	19
Chassis weight	20
Processor specifications	20
Supported operating systems	20
System battery	20
Expansion bus specifications	20
Memory specifications	21
Drives and storage specifications	21
Video specifications	21
Environmental specifications	22
Standard operating temperature specifications	22
Expanded operating temperature specifications	30
Operating temperature derating specifications	31
Relative humidity specifications	31
Temperature specifications	31
Thermal restrictions	31
Particulate and gaseous contamination specifications	34
Maximum vibration specifications	34
Maximum shock specifications	34
Maximum altitude specifications	35
Fresh Air Operation	35
Initial system setup and configuration	36
Setting up your system	36
iDRAC configuration	36
Options to set up iDRAC IP address	36
Log in to iDRAC	37
Options to install the operating system	37
Methods to download firmware and drivers	37
Downloading drivers and firmware	38
Pre-operating system management applications	39
Options to manage the pre-operating system applications	39
System Setup	39
Viewing System Setup	39
System Setup details	40
System BIOS	40
Viewing System BIOS	40
System BIOS Settings details	40
System Information	41
Viewing System Information	41
System Information details	41
Memory Settings	42
Viewing Memory Settings	42
Memory Settings details	42
Processor Settings	43
Viewing Processor Settings	43
Processor Settings details	43
SATA Settings	45
Viewing SATA Settings	45
SATA Settings details	45
NVMe Settings	45
Viewing NVMe Settings	46
NVMe Settings details	46
Boot Settings	46
Viewing Boot Settings	46
Boot Settings details	47
Choosing system boot mode	47
Changing boot order	47
Network Settings	48
Viewing Network Settings	48
Network Settings screen details	48
Integrated Devices	49
Viewing Integrated Devices	49
Integrated Devices details	49
Serial Communication	51
Viewing Serial Communication	51
Serial Communication details	51
System Profile Settings	52
Viewing System Profile Settings	52
System Profile Settings details	52
System Security	53
Viewing System Security	53
System Security Settings details	53
Creating a system and setup password	55
Using your system password to secure the system	56
Deleting or changing system and setup password	56
Operating with setup password enabled	56
Redundant OS Control	57
Viewing Redundant OS Control	57
Redundant OS Control screen details	57
Miscellaneous Settings	58
Viewing Miscellaneous Settings	58
Miscellaneous Settings details	58
iDRAC Settings utility	58
Device Settings	59
Dell Lifecycle Controller	59
Embedded system management	59
Boot Manager	59
Viewing Boot Manager	59
Boot Manager main menu	59
One-shot UEFI boot menu	60
System Utilities	60
PXE boot	60
Installing and removing enclosure components	61
Safety instructions	61
Before working inside your system	61
After working inside your system	62
Recommended tools	62
Dell EMC PowerEdge C6420 sled	62
Sled Installation Guidelines	62
Removing a sled	63
Installing a sled	65
PERC battery	66
Removing the PERC battery	66
Installing the PERC battery	67
Air shroud	68
Removing the air shroud	68
Installing the air shroud	69
System memory	70
System memory guidelines	70
General memory module installation guidelines	71
Mode-specific guidelines	71
Removing a memory module	73
Installing a memory module	74
Support bracket	75
Removing the support bracket	75
Installing the support bracket	76
Linking board and PCIe cable	77
Removing the linking board and PCIe cables	77
Installing the linking board and PCIe cables	78
Processor and heat sink module	79
Removing a processor and heat sink module	80
Installing a processor and heat sink module	81
Removing the fabric processor from the processor heat sink module	83
Installing the fabric processor into the processor heat sink module	84
Removing the non-fabric processor from the processor and heat sink module	86
Installing the non-fabric processor into a processor and heat sink module	89
Removing the fabric and sideband cables	91
Installing the fabric and sideband cables	92
Expansion cards	93
PCIe slot priority	93
Removing the expansion card riser assembly	95
Installing the expansion card riser assembly	96
Removing an expansion card	97
Installing an expansion card	98
Removing the riser card	100
Installing the riser card	100
Removing the M.2 SATA x16 riser	101
Installing the M.2 SATA x16 riser	102
Removing the M.2 SATA card	103
Installing the M.2 SATA card	104
M.2 SSD module	105
Removing the M.2 SATA x16 riser	106
Installing the M.2 SATA x16 riser	106
Removing the M.2 SATA card	107
Installing the M.2 SATA card	108
Mezzanine and OCP cards	110
Removing a mezzanine card	110
Installing a mezzanine card	111
Removing the mezzanine card bridge board	112
Installing the mezzanine card bridge board	113
Removing the OCP card	114
Installing the OCP card	115
System battery	116
Replacing system battery	116
Installing the system battery	117
System board	118
Removing the system board	118
Installing system board	119
Restoring the Service Tag by using the Easy Restore feature	120
Entering the system Service Tag by using System Setup	121
Trusted Platform Module	121
Upgrading the Trusted Platform Module	121
Removing the TPM	122
Installing the TPM	122
Initializing TPM for BitLocker users	122
Initializing the TPM 1.2 for TXT users	123
Initializing the TPM 2.0 for TXT users	123
System diagnostics	124
Dell Embedded System Diagnostics	124
Running the Embedded System Diagnostics from Boot Manager	124
Running the Embedded System Diagnostics from the Dell Lifecycle Controller	124
System diagnostic controls	125
Jumpers and connectors	126
System board jumper settings	126
System board connectors	126
Disabling forgotten password	127
Getting help	128
Contacting Dell EMC	128
Documentation feedback	128
Accessing system information by using QRL	128
Quick Resource Locator for C6400 and C6420 systems	129
Receiving automated support with SupportAssist	129