Dell PowerEdge C6420 EMC Installation and Service Manual - Page 111

Installing a mezzanine card

Get Dell PowerEdge C6420 PDF manuals and user guides View all Dell PowerEdge C6420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

Figure 65. Removing a mezzanine card Next steps 1. Install the mezzanine card or install the mezzanine card filler bracket. Installing a mezzanine card Prerequisites NOTE: The procedure to install the mezzanine blank is similar to the removal of a mezzanine card. 1. Follow the safety guidelines listed in Safety instructions. Steps 1. Attach and secure the mezzanine card bracket to the mezzanine card. 2. Holding the card by its edges, position the card so that the card edge connector aligns with the connector of the bridge board on the system board. 3. Insert the card edge connector and push the card firmly until the card is fully seated on the bridge board. Installing and removing enclosure components 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Figure 65. Removing a mezzanine card
Next steps
1.
Install the mezzanine card
or
install the mezzanine card filler bracket
.
Installing a mezzanine card
Prerequisites
NOTE:
The procedure to install the mezzanine blank is similar to the removal of a mezzanine card.
1.
Follow the safety guidelines listed in
Safety instructions
.
Steps
1.
Attach and secure the mezzanine card bracket to the mezzanine card.
2.
Holding the card by its edges, position the card so that the card edge connector aligns with the connector of the bridge board on the
system board.
3.
Insert the card edge connector and push the card firmly until the card is fully seated on the bridge board.
Installing and removing enclosure components
111