Home » Dell Manuals » Servers » Dell PowerEdge MX7000 » Manual Viewer

Dell PowerEdge MX7000 EMC OpenManage Enterprise-Modular Edition Version 1.00.1 - Page 59

Configuring IOM network settings, Configuring root password, Configuring SNMP settings

View all Dell PowerEdge MX7000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Configuring IOM network settings The network settings for IOMs include configuring the public management IP for the selected management port. To configure the networking settings: 1 Click All Devices > I/O Modules > View Details > Settings > Network or Devices > I/O Modules > View Details > Settings > Network. 2 In the IPv4 Settings section, select Enable IPv4. 3 Enter the IP Address, Subnet Mask, and Gateway for the management port. The IP Address, Subnet Mask, and Gateway options are enabled only if the Enable DHCP check box is cleared. 4 In the IPv6 Settings section, select Enable IPv6. 5 Enter the IPv6 Address, select the Prefix Length. The IPv6 Address, Prefix Length, and Gateway options are enabled only if the Enable Autoconfiguration check box is cleared. 6 Enter the Gateway for the management port. The IPv6 Address, Prefix Length, and Gateway options are enabled only if the Enable Autoconfiguration check box is cleared. NOTE: For tagged or untagged VLAN network, any IPv6 setting configured using OME - Modular may not have the default gateway. To get the default gateway, go to the respective OS10 CLI and enable Stateless Address Autoconfiguration (SLAAC) on the respective tagged or untagged VLAN. 7 In the DNS Server Settings section, enter the Preferred DNS Server, Alternate DNS Server 1, and Alternate DNS Server 2 addresses. For MXG610s IOMs, you can set the Preferred DNS and Alternate Server 1 and 2 addresses. However, the server address for Alternate DNS Server 2 is not applied though the response is successful as, MXG610s IOMs support only two server address for DNS settings. 8 In the Management VLAN section, select Enable VLAN and enter the VLAN ID. For MXG610s FC IOMs, DHCP works only without VLAN while Static IP works with or without VLAN configuration. To change the IP configuration from DHCP IP to Static IP, perform the following steps: a Disable DHCP, configure the static IP, and save the configuration. b Enable VLAN, configure the VLAN ID, and save the configuration. Configuring root password To configure the root password: 1 Click All Devices > I/O Modules > View Details > Settings > Management or Devices > I/O Modules > View Details > Settings > Management. The I/O Modules page is displayed. 2 Enter the Host Name and Root Password for the IOM. Configuring SNMP settings To configure the SNMP settings: 1 Click All Devices > I/O Modules > View Details > Settings > Monitoring or Devices > I/O Modules > View Details > Settings > Monitoring. 2 Select Enable SNMP to configure the SNMP version and community string. Ethernet IO Modules 59

Section	Page
Dell EMC OpenManage Enterprise-Modular Edition Version 1.00.10 for PowerEdge MX7000 Chassis User's Guide	3
Overview	8
Key features	8
New in this release	9
Supported platforms	9
Supported web browsers	9
Other documents you may need	9
Accessing documents from Dell support site	10
Positioning OME-Modular with other Dell EMC applications	11
Updating the management module firmware	12
Logging in to OME-Modular	13
Logging in to OME–Modular as local, Active Directory, or LDAP user	13
Logging in to OME-Modular as Active Directory or LDAP user	14
OME-Modular home page	14
Viewing alerts	15
Viewing jobs and activities	15
Multi-chassis management dashboard	15
Viewing device health	16
Setting up chassis	16
Initial configuration	17
Configuring chassis settings	18
Configuring chassis power	18
Configuring chassis network	18
Configuring chassis network services	19
Configuring local access	20
Configuring chassis location	21
Configuring Quick Deploy options	21
Managing chassis	21
Creating chassis filters	22
Viewing chassis overview	22
Chassis groups	23
Prerequisites for creating a wired group	23
Creating chassis groups	25
Controlling chassis power	26
Backing up chassis	26
Restoring chassis	27
Exporting chassis profiles	27
Managing chassis failover	27
Troubleshooting in chassis	28
Blinking LEDs	28
Interfaces to access OME-Modular	28
Viewing chassis hardware	29
Viewing chassis alerts	30
Viewing chassis hardware logs	30
Configuring OME–Modular	30
Viewing current configuration	31
Configuring users and user settings	32
Configuring login security settings	36
Configuring alerts	37
Managing compute sleds	39
Viewing compute overview	39
Configuring compute settings	41
Configuring compute network settings	41
Viewing compute hardware	41
Viewing compute firmware	41
Viewing compute hardware logs	42
Viewing compute alerts	42
Managing Storage	43
Storage overview	43
Performing a storage system reseat	43
Blinking LED	44
Editing storage sled assignments	44
Other information	44
Viewing hardware details	44
Viewing drive details	45
Assigning drives to a compute sled	45
Assigning storage enclosure to a compute sled	45
Updating enclosure firmware	46
Downgrading storage enclosure firmware	47
Managing SAS IOMs	47
SAS IOM Overview	47
Force active	48
Clearing configuration	48
Extracting IOM logs	49
Managing templates	50
Viewing template details	50
Creating templates	51
Importing templates	51
Deploying templates	51
Editing templates	52
Editing template networks	52
Cloning templates	52
Exporting templates	52
Deleting templates	52
Managing identity pools	54
Creating identity pools	54
Editing identity pools	56
Exporting identity pools	56
Deleting identity pools	56
Ethernet IO Modules	57
Managing Ethernet IOMs	57
Viewing hardware details	58
Configuring IOM settings	58
Configuring IOM network settings	59
Configuring root password	59
Configuring SNMP settings	59
Configuring advanced settings	60
Configuring ports	60
MX scalable fabric architecture	62
Architectural Overview	62
Fabric Switching Engine	62
Fabric Expander Module	62
Recommended physical topology	63
Restrictions and guidelines	64
Recommended connection order	64
SmartFabric Services	65
Changing operating modes	65
Guidelines for operating in SmartFabric mode	66
SmartFabric network topologies	66
2 x MX9116n Fabric Switching Engines in separate chassis	66
2 x MX5108n Ethernet Switches in the same chassis	67
2 x MX9116n Fabric Switching Engines in the same chassis	67
Switch to switch cabling	67
Upstream network switch requirements	68
Spanning Tree Protocol	68
NIC teaming restrictions	69
CLI commands available in Fabric mode	69
Viewing fabric details	70
Adding fabric	70
Adding uplinks	70
Adding network	71
Editing uplink	71
Viewing topology details	72
Editing fabric details	72
Deleting uplinks	72
Deleting fabric	72
Managing networks	74
SmartFabric VLAN management and automated QoS	74
Defining networks	75
Editing networks	75
Exporting network configurations	76
Deleting network configurations	76
Managing Fibre Channel IOMs	77
Managing firmware	78
Creating baselines	79
Checking compliance	79
Editing baselines	79
Managing catalogs	79
Viewing catalogs	80
Adding catalogs	80
Updating firmware	81
Rolling back firmware	81
Deleting firmware	82
Monitoring alerts and logs	83
Alert log	83
Filtering alert logs	83
Acknowledging alert logs	84
Unacknowledging alert logs	84
Ignoring alert logs	84
Exporting alert logs	84
Deleting alert logs	85
Alert policies	85
Creating alert policies	85
Enabling alert policies	86
Editing alert policies	86
Disabling alert policies	86
Deleting alert policies	86
Alert definitions	87
Filtering alert definitions	87
Monitoring audit logs	88
Filtering audit logs	88
Exporting audit logs	88
Monitoring jobs	89
Filtering jobs	89
Viewing job details	90
Running jobs	91
Stopping jobs	91
Enabling jobs	91
Disabling jobs	91
Deleting jobs	91
Troubleshooting	92
Storage	92
Firmware update is failing	92
Storage assignment is failing	92
SAS IOM status is downgraded	92
SAS IOM health is downgraded	92
Drives on compute sled are not visible	93
Storage configuration cannot be applied to SAS IOMs	93
Drives in OpenManage are not visible	93
iDRAC and OpenManage drive information do not match	93
The assignment mode of storage sled is unknown	93
Recommended slot configurations for IOMs	94

Match case Limit results 1 per page

Conﬁguring

IOM network settings

The network settings for IOMs include

conﬁguring

the public management IP for the selected management port.

conﬁgure

the networking settings:

Click

All Devices

I/O Modules

View Details

Settings

Network

Devices

I/O Modules

View Details

Settings

Network

In the

IPv4 Settings

section, select

Enable IPv4

Enter the

IP Address

Subnet Mask

, and

Gateway

for the management port.

The

IP Address

Subnet Mask

, and

Gateway

options are enabled only if the

Enable DHCP

check box is cleared.

In the

IPv6 Settings

section, select

Enable IPv6

Enter the

IPv6 Address

, select the

Preﬁx

Length

The

IPv6 Address

Preﬁx

Length

, and

Gateway

options are enabled only if the

Enable

Autoconﬁguration

check box is cleared.

Enter the

Gateway

for the management port.

The

IPv6 Address

Preﬁx

Length

, and

Gateway

options are enabled only if the

Enable

Autoconﬁguration

check box is cleared.

NOTE:

For tagged or untagged VLAN network, any IPv6 setting

conﬁgured

using OME - Modular may not have the

default gateway. To get the default gateway, go to the respective OS10 CLI and enable Stateless Address

Autoconﬁguration

(SLAAC) on the respective tagged or untagged VLAN.

In the

DNS Server Settings

section, enter the

Preferred DNS Server

Alternate DNS Server 1

, and

Alternate DNS Server 2

addresses.

For MXG610s IOMs, you can set the Preferred DNS and Alternate Server 1 and 2 addresses. However, the server address for

Alternate DNS Server 2

is not applied though the response is successful as, MXG610s IOMs support only two server address for DNS

settings.

In the

Management VLAN

section, select

Enable VLAN

and enter the

VLAN ID

For MXG610s FC IOMs, DHCP works only without VLAN while Static IP works with or without VLAN

conﬁguration.

To change the IP

conﬁguration

from DHCP IP to Static IP, perform the following steps:

Disable DHCP,

conﬁgure

the static IP, and save the

conﬁguration.

Enable VLAN,

conﬁgure

the VLAN ID, and save the

conﬁguration.

Conﬁguring

root password

conﬁgure

the root password:

Click

All Devices

I/O Modules

View Details

Settings

Management

Devices

I/O Modules

View Details

Settings

Management

The

I/O Modules

page is displayed.

Enter the

Host Name

and

Root Password

for the IOM.

Conﬁguring

SNMP settings

conﬁgure

the SNMP settings:

Click

All Devices

I/O Modules

View Details

Settings

Monitoring

Devices

I/O Modules

View Details

Settings

Monitoring

Select

Enable SNMP

conﬁgure

the SNMP version and community string.

Ethernet IO Modules