Dell PowerEdge MX7000 EMC OpenManage Enterprise-Modular Edition Version 1.00.1 - Page 65

SmartFabric Services, Changing operating modes

Get Dell PowerEdge MX7000 PDF manuals and user guides View all Dell PowerEdge MX7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

10 SmartFabric Services SmartFabric Services is a capability of Dell EMC Networking OS10 Enterprise Edition running on Ethernet switches designed for the PowerEdge MX platform. A SmartFabric is a logical entity containing a collection of physical resources such as servers and switches and logical resources- networks, templates, and uplinks. In the SmartFabric Services mode, the switches operate as a simple Layer 2 input output aggregation device, which enables complete interoperability with network equipment vendors. A SmartFabric provides: • Data center Modernization - I/O Aggregation - Plug-and-play fabric deployment - A single interface to manage all switches in the fabric like a single logical switch • Lifecycle Management - Fabric-wide firmware upgrade scheduling - Automated or user enforced roll back to last well-known state • Fabric Automation - Ensured compliance with selected physical topology - Policy based Quality of Service (QoS) based on VLAN and Priority assignments - Automatic detection of fabric misconfigurations and link level failure conditions - Automated healing of the fabric on failure condition removal • Failure Remediation - Dynamically adjusts bandwidth across all inter-switch links in the event of a link failure Unlike Full Switch mode, most fabric configuration settings are performed using the OME-Modular. For information about automated QoS, see SmartFabric VLAN management and automated QoS Changing operating modes In both Full Switch and Fabric modes, all configuration changes you make using the OME-Modular interface are retained when you switch modes. It is recommended that you use the GUI for all switch configurations in Fabric mode and the OS10 CLI for configuring switches in Full Switch mode. To switch an MX9116n Fabric Switching Engine or MX5108n Ethernet Switch between Full Switch and Fabric modes, use the OME- Modular GUI and create a fabric with that switch. When that switch is added to the fabric, it automatically changes to Fabric mode. When you change from Full Switch to Fabric mode, all Full Switch CLI configuration changes are deleted except for a subset of settings supported in Fabric mode. To change a switch from Fabric to Full Switch mode, the fabric must be deleted. At that time, all Fabric GUI configuration settings are deleted. However, the configurations supported by the subset of Fabric CLI commands (hostname, SNMP settings, and so on) and the changes you make to port interfaces, MTU, speed, and auto-negotiation mode, are not deleted. The changes to port interfaces exclude the administrator state-shutdown/no shutdown. Topics: SmartFabric Services 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
SmartFabric Services
SmartFabric Services is a capability of Dell EMC Networking OS10 Enterprise Edition running on Ethernet switches designed for the
PowerEdge MX platform.
A SmartFabric is a logical entity containing a collection of physical resources such as servers and switches and logical resources—
networks, templates, and uplinks. In the SmartFabric Services mode, the switches operate as a simple Layer 2 input output aggregation
device, which enables complete interoperability with network equipment vendors.
A SmartFabric provides:
•
Data center Modernization
–
I/O Aggregation
–
Plug-and-play fabric deployment
–
A single interface to manage all switches in the fabric like a single logical switch
•
Lifecycle Management
–
Fabric-wide
firmware
upgrade scheduling
–
Automated or user enforced roll back to last well-known state
•
Fabric Automation
–
Ensured compliance with selected physical topology
–
Policy based Quality of Service (QoS) based on VLAN and Priority assignments
–
Automatic detection of fabric
misconfigurations
and link level failure conditions
–
Automated healing of the fabric on failure condition removal
•
Failure Remediation
–
Dynamically adjusts bandwidth across all inter-switch links in the event of a link failure
Unlike Full Switch mode, most fabric
configuration
settings are performed using the OME-Modular.
For information about automated QoS, see
SmartFabric VLAN management and automated QoS
Changing operating modes
In both Full Switch and Fabric modes, all
configuration
changes you make using the OME–Modular interface are retained when you switch
modes. It is recommended that you use the GUI for all switch
configurations
in Fabric mode and the OS10 CLI for
configuring
switches in
Full Switch mode.
To switch an MX9116n Fabric Switching Engine or MX5108n Ethernet Switch between Full Switch and Fabric modes, use the OME–
Modular GUI and create a fabric with that switch. When that switch is added to the fabric, it automatically changes to Fabric mode. When
you change from Full Switch to Fabric mode, all Full Switch CLI
configuration
changes are deleted except for a subset of settings
supported in Fabric mode.
To change a switch from Fabric to Full Switch mode, the fabric must be deleted. At that time, all Fabric GUI
configuration
settings are
deleted. However, the
configurations
supported by the subset of Fabric CLI commands (hostname, SNMP settings, and so on) and the
changes you make to port interfaces, MTU, speed, and auto-negotiation mode, are not deleted. The changes to port interfaces exclude the
administrator state—shutdown/no shutdown.
Topics:
10
SmartFabric Services
65