Dell PowerEdge R210 II Owner's Manual - Page 44

Baseboard Management Controller Configuration, Entering the BMC Setup Module - firmware

Get Dell PowerEdge R210 II PDF manuals and user guides View all Dell PowerEdge R210 II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

When an optional iDRAC6 Express card is installed, Dell USC provides the following additional features: • Downloading and applying firmware updates • Configuring hardware and firmware For more information about setting up Dell USC, configuring hardware and firmware, and deploying the operating system, see the Unified Server Configurator documentation at support.dell.com/manuals. Baseboard Management Controller Configuration The BMC enables configuring, monitoring, and recovery of systems remotely. The BMC provides the following features: • Enables fault logging and SNMP alerting • Provides access to system event log and sensor status • Allows control of system functions including power on and off • Functions independently of the system's power state or the system's operating system • Provides text console redirection for system setup, text-based utilities, and operating system consoles NOTE: To remotely access the BMC through the integrated NIC, you must connect the network connection to integrated NIC1. For additional information on using BMC, see the documentation for the BMC and systems management applications at support.dell.com/manuals. Entering the BMC Setup Module 1 Turn on or restart your system. 2 Press when prompted after POST. If your operating system begins to load before you press , allow the system to finish booting, and then restart your system and try again. 44 Using the System Setup Program and Boot Manager

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
44
Using the System Setup Program and Boot Manager
When an optional iDRAC6 Express card is installed, Dell USC provides the
following additional features:
•
Downloading and applying firmware updates
•
Configuring hardware and firmware
For more information about setting up Dell USC, configuring hardware and
firmware, and deploying the operating system, see the Unified Server
Configurator documentation at
support.dell.com/manuals
.
Baseboard Management Controller Configuration
The BMC enables configuring, monitoring, and recovery of systems remotely.
The BMC provides the following features:
•
Enables fault logging and SNMP alerting
•
Provides access to system event log and sensor status
•
Allows control of system functions including power on and off
•
Functions independently of the system’s power state or the system’s
operating system
•
Provides text console redirection for system setup, text-based utilities, and
operating system consoles
NOTE:
To remotely access the BMC through the integrated NIC, you must connect
the network connection to integrated NIC1.
For additional information on using BMC, see the documentation for the
BMC and systems management applications at
support.dell.com/manuals
.
Entering the BMC Setup Module
1
Turn on or restart your system.
2
Press <Ctrl><E> when prompted after POST.
If your operating system begins to load before you press <Ctrl><E>,
allow the system to finish booting, and then restart your system and try
again.