Dell PowerEdge SC1435 Hardware Owner's Manual - Page 18

See Using the System Setup, Troubleshooting a USB Device - hard drive

Get Dell PowerEdge SC1435 PDF manuals and user guides View all Dell PowerEdge SC1435 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Table 1-6. System Messages (continued) Message General failure Invalid NVRAM configuration, Resource Re-allocated Keyboard Controller failure Manufacturing mode detected Memory address line failure at address, read value expecting value Causes The operating system is unable to carry out the command. System detected and corrected a resource conflict. Faulty keyboard controller; faulty system board System is in manufacturing mode. Faulty or improperly installed memory modules. Corrective Actions This message is usually followed by specific information. Note the information and take the appropriate action to resolve the problem. No action is required. See "Getting Help" on page 95. Reboot to take the system out of manufacturing mode. See "Troubleshooting System Memory" on page 76. Memory double word logic failure at address, read value expecting value Memory odd/even logic failure at address, read value expecting value Memory write/read failure at address, read value expecting value Memory tests terminated POST memory test terminated by Information only. by keystroke. pressing the spacebar. No boot device available Faulty or missing optical/diskette Use a bootable diskette, CD, or hard drive subsystem, hard drive, or hard- drive. If the problem persists, see drive subsystem, or no boot disk in "Troubleshooting a USB Device" on drive A. page 71, "Troubleshooting an Optical Drive" on page 78, and "Troubleshooting a Hard Drive" on page 78. See "Using the System Setup Program" on page 23 for information about setting the order of boot devices. 18 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
18
About Your System
General failure
The operating system is unable to
carry out the command.
This message is usually followed by
specific information. Note the
information and take the appropriate
action to resolve the problem.
Invalid NVRAM
configuration, Resource
Re-allocated
System detected and corrected a
resource conflict.
No action is required.
Keyboard Controller
failure
Faulty keyboard controller; faulty
system board
See "Getting Help" on page 95.
Manufacturing mode
detected
System is in manufacturing mode.
Reboot to take the system out of
manufacturing mode.
Memory address line
failure at
address
, read
value
expecting
value
Faulty or improperly installed
memory modules.
See "Troubleshooting System Memory"
on page 76.
Memory double word logic
failure at
address
, read
value
expecting
value
Memory odd/even logic
failure at
address,
read
value
expecting
value
Memory write/read failure
at
address
, read
value
expecting
value
Memory tests terminated
by keystroke.
POST memory test terminated by
pressing the spacebar.
Information only.
No boot device available
Faulty or missing optical/diskette
drive subsystem, hard drive, or hard-
drive subsystem, or no boot disk in
drive A.
Use a bootable diskette, CD, or hard
drive. If the problem persists, see
"Troubleshooting a USB Device" on
page 71, "Troubleshooting an Optical
Drive" on page 78, and
"Troubleshooting a Hard Drive" on
page 78. See "Using the System Setup
Program" on page 23 for information
about setting the order of boot devices.
Table 1-6.
System Messages
(continued)
Message
Causes
Corrective Actions