Dell PowerEdge SC1435 Hardware Owner's Manual - Page 42

Power Supply, Removing the Power Supply

Get Dell PowerEdge SC1435 PDF manuals and user guides View all Dell PowerEdge SC1435 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

5 Reinstall the cooling shroud. See "Replacing the Cooling Shroud" on page 40. 6 Close the system. See "Opening and Closing the System" on page 38. Power Supply Removing the Power Supply 1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals. 2 Open the system. See "Opening and Closing the System" on page 38. 3 Disconnect the power cable from the power supply and remove the cable from the cable retention bracket. NOTICE: On a rack system, you may need to temporarily unlatch and lift the cable management arm. For information about the cable management arm, see the system's Rack Installation Guide. 4 Disconnect the two power supply cables from the POWER1 and POWER2 connectors on the system board. See Figure 6-1. 5 If applicable, disconnect the hard drive power cables from the hard drive(s). 6 Remove the screw at the front of the power supply that secures the power supply to the chassis. See Figure 3-6. 7 Slide the power supply toward the front of the system and remove it from the system. 42 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
42
Installing System Components
5
Reinstall the cooling shroud. See "Replacing the Cooling Shroud" on page 40.
6
Close the system. See "Opening and Closing the System" on page 38.
Power Supply
Removing the Power Supply
1
Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and
peripherals.
2
Open the system. See "Opening and Closing the System" on page 38.
3
Disconnect the power cable from the power supply and remove the cable from the cable retention
bracket.
NOTICE:
On a rack system, you may need to temporarily unlatch and lift the cable management arm. For
information about the cable management arm, see the system’s
Rack Installation Guide
.
4
Disconnect the two power supply cables from the POWER1 and POWER2 connectors on the system
board. See Figure 6-1.
5
If applicable, disconnect the hard drive power cables from the hard drive(s).
6
Remove the screw at the front of the power supply that secures the power supply to the chassis. See
Figure 3-6.
7
Slide the power supply toward the front of the system and remove it from the system.