Dell PowerEdge SC1435 Hardware Owner's Manual - Page 19

PCIe Fatal Error caused a, Plug & Play Configuration

Get Dell PowerEdge SC1435 PDF manuals and user guides View all Dell PowerEdge SC1435 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Table 1-6. System Messages (continued) Message Causes Corrective Actions No boot sector on hard drive Incorrect configuration settings in System Setup program, or no operating system on hard drive. Check the hard-drive configuration settings in the System Setup program. See "Using the System Setup Program" on page 23. If necessary, install the operating system on your hard drive. See your operating system documentation. No timer tick interrupt Faulty system board. See "Getting Help" on page 95. Not a boot diskette No operating system on diskette. Use a bootable diskette. PCIe Degraded Link Width Error: Embedded Bus#nn/Dev#nn/Funcn Expected Link Width is n Actual Link Width is n Faulty or improperly installed PCIe card in the specified slot. Reseat the PCIe card in the specified slot number. See "Installing an Expansion Card" on page 44. If the problem persists, see "Getting Help" on page 95. PCIe Degraded Link Width Error: Slot n Expected Link Width is n Actual Link Width is n Faulty or improperly installed PCIe card in the specified slot. Reseat the PCIe card in the specified slot number. See "Installing an Expansion Card" on page 44. If the problem persists, see "Getting Help" on page 95. PCIe Fatal Error caused a system reset: Slot n or Embedded Bus#nn/Dev#nn/Funcn Faulty or improperly installed PCIe card in the specified slot. Reseat the PCIe card in the specified slot number. See "Installing an Expansion Card" on page 44. If the problem persists, see "Getting Help" on page 95. Please check the system event log for details. PCI BIOS failed to install PCI device BIOS (Option ROM) Reseat the expansion cards. Ensure checksum failure is detected during that all appropriate cables are securely shadowing. Loose cables to connected to the expansion cards. If expansion card(s); faulty or the problem persists, see improperly installed expansion card. "Troubleshooting an Expansion Card" on page 80. Plug & Play Configuration Error encountered in initializing Error PCI device; faulty system board. Install the NVRAM_CLR jumper and reboot the system. See Figure 6-1 for jumper location. If the problem persists, see "Troubleshooting an Expansion Card" on page 80. About Your System 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
About Your System
19
No boot sector on hard
drive
Incorrect configuration settings in
System Setup program, or no
operating system on hard drive.
Check the hard-drive configuration
settings in the System Setup program.
See "Using the System Setup Program"
on page 23. If necessary, install the
operating system on your hard drive.
See your operating system
documentation.
No timer tick interrupt
Faulty system board.
See "Getting Help" on page 95.
Not a boot diskette
No operating system on diskette.
Use a bootable diskette.
PCIe Degraded Link Width
Error: Embedded
Bus#
nn
/Dev#
nn
/Func
n
Expected Link Width is
n
Actual Link Width is
n
Faulty or improperly installed PCIe
card in the specified slot.
Reseat the PCIe card in the specified
slot number. See "Installing an
Expansion Card" on page 44. If the
problem persists, see "Getting Help"
on page 95.
PCIe Degraded Link Width
Error: Slot
n
Expected Link Width is
n
Actual Link Width is
n
Faulty or improperly installed PCIe
card in the specified slot.
Reseat the PCIe card in the specified
slot number. See "Installing an
Expansion Card" on page 44. If the
problem persists, see "Getting Help"
on page 95.
PCIe Fatal Error caused a
system reset: Slot
n
or
Embedded
Bus#
nn
/Dev#
nn
/Func
n
Please check the system
event log for details.
Faulty or improperly installed PCIe
card in the specified slot.
Reseat the PCIe card in the specified
slot number. See "Installing an
Expansion Card" on page 44. If the
problem persists, see "Getting Help"
on page 95.
PCI BIOS failed to
install
PCI device BIOS (Option ROM)
checksum failure is detected during
shadowing. Loose cables to
expansion card(s); faulty or
improperly installed expansion card.
Reseat the expansion cards. Ensure
that all appropriate cables are securely
connected to the expansion cards. If
the problem persists, see
"Troubleshooting an Expansion Card"
on page 80.
Plug & Play Configuration
Error
Error encountered in initializing
PCI device; faulty system board.
Install the NVRAM_CLR jumper and
reboot the system. See Figure 6-1 for
jumper location. If the problem
persists, see "Troubleshooting an
Expansion Card" on page 80.
Table 1-6.
System Messages
(continued)
Message
Causes
Corrective Actions