Dell PowerVault MD3260i CLI Guide - Page 211

Start Physical Disk Channel Blink, Start Physical Disk Channel Fault Isolation Diagnostics

Get Dell PowerVault MD3260i PDF manuals and user guides View all Dell PowerVault MD3260i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 211 highlights

Start Physical Disk Channel Blink This command identifies the expansion enclosures that are connected to a specific physical disk port by turning on the indicator lights for the expansion enclosure that is connected to the physical disk port. Use the stop physicalDiskChannel blink command to turn off the indicator lights on the expansion enclosure. Syntax start physicalDiskChannel [(1 | 2)] blink Parameter Parameter Description physicalDiskChannel The identifier number of the physical disk channel that you want to locate. Valid values for the identifier number are 1 or 2. Enclose the identifier number in square brackets ([ ]). Start Physical Disk Channel Fault Isolation Diagnostics This command runs the physical disk channel fault isolation diagnostics and stores the results. Syntax start physicalDiskChannel [(1 | 2)] controller [(0 | 1)] faultDiagnostics testDevices=[(all | controller=(0 | 1) | emms=[enclosureID1 slotID1, enclosureID2 slotID2... enclosureIDn slotIDn] | physicalDisks= (enclosureID1,slotID1... enclosureIDn,slotIDn)] | (dataPattern=(fixed | pseudoRandom) | patternNumber=[(0xhexadecimal | number)] | maxErrorCount=integer | testIterations=integer | timeout=timeInterval) Parameters Parameter physicalDiskChannel controller Description The identifier number of the physical disk channel that you want to locate. Valid values for the identifier number are 1 or 2. Enclose the identifier number in square brackets ([ ]). The identifier letter of the RAID controller module that you want to test. Valid RAID controller module identifier values are 0 and 1. The identifier value is 0 for the RAID controller module on the top and 1 for the RAID controller module on the bottom when viewed from the rear of the enclosure. testDevices The identifiers of the devices (RAID controller modules, EMMs, or physical disks) that you want to test. You can specify all or enter the specific identifiers for the devices that you want to diagnose. dataPattern The method of repeatability that you want to test. 211

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
Start Physical Disk Channel Blink
This command identifies the expansion enclosures that are connected to a specific physical disk port by turning on the
indicator lights for the expansion enclosure that is connected to the physical disk port. Use the stop
physicalDiskChannel blink
command to turn off the indicator lights on the expansion enclosure.
Syntax
start physicalDiskChannel [(1 | 2)] blink
Parameter
Parameter
Description
physicalDiskChannel
The identifier number of the physical disk channel that you
want to locate. Valid values for the identifier number are
1
or
2
. Enclose the identifier number in square brackets ([ ]).
Start Physical Disk Channel Fault Isolation Diagnostics
This command runs the physical disk channel fault isolation diagnostics and stores the results.
Syntax
start physicalDiskChannel [(1 | 2)]
controller [(0 | 1)] faultDiagnostics
testDevices=[(all | controller=(0 | 1) |
emms=[
enclosureID1
slotID1,
enclosureID2
slotID2...
enclosureIDn
slotIDn]
|
physicalDisks= (
enclosureID1,slotID1... enclosureIDn,slotIDn
)]
| (dataPattern=(fixed | pseudoRandom) |
patternNumber=[(
0xhexadecimal
|
number
)] |
maxErrorCount=
integer
| testIterations=
integer
|
timeout=
timeInterval
)
Parameters
Parameter
Description
physicalDiskChannel
The identifier number of the physical disk channel that you
want to locate. Valid values for the identifier number are
1
or
2
. Enclose the identifier number in square brackets ([ ]).
controller
The identifier letter of the RAID controller module that you
want to test. Valid RAID controller module identifier values
are
0
and
1
. The identifier value is
0
for the RAID
controller module on the top and
1
for the RAID controller
module on the bottom when viewed from the rear of the
enclosure.
testDevices
The identifiers of the devices (RAID controller modules,
EMMs, or physical disks) that you want to test. You can
specify all or enter the specific identifiers for the devices
that you want to diagnose.
dataPattern
The method of repeatability that you want to test.
211