Dell Vostro 15 3510 Service Manual - Page 47

Touchpad, Removing the touchpad assembly

Get Dell Vostro 15 3510 PDF manuals and user guides View all Dell Vostro 15 3510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Steps 1. Align and place the I/O board under the left hinge assembly and on to the palm-rest and keyboard assembly. 2. Replace the two (M2x3) screws to secure the I/O daughter board to the palm-rest and keyboard assembly. 3. Replace the three (M2x3) screws to secure the I/O daughter board to the palm-rest and keyboard assembly. 4. Connect the fingerprint-reader board cable to the connector on the I/O board and close the latch, if applicable. 5. Connect the I/O-board power cable to the connector on the I/O board and close the latch. Next steps 1. Install the base cover. 2. Exit service mode. 3. Install the SD card. 4. Follow the procedure in after working inside your computer. Touchpad Removing the touchpad assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3. Remove the base cover. 4. Remove the battery. About this task The following images indicate the location of the touchpad and provides a visual representation of the removal procedure. Removing and installing components 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Steps
1.
Align and place the I/O board under the left hinge assembly and on to the palm-rest and keyboard assembly.
2.
Replace the two (M2x3) screws to secure the I/O daughter board to the palm-rest and keyboard assembly.
3.
Replace the three (M2x3) screws to secure the I/O daughter board to the palm-rest and keyboard assembly.
4.
Connect the fingerprint-reader board cable to the connector on the I/O board and close the latch, if applicable.
5.
Connect the I/O-board power cable to the connector on the I/O board and close the latch.
Next steps
1.
Install the
base cover
.
2.
Exit
service mode
.
3.
Install the
SD card
.
4.
Follow the procedure in
after working inside your computer
.
Touchpad
Removing the touchpad assembly
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
SD card
.
3.
Remove the
base cover
.
4.
Remove the
battery
.
About this task
The following images indicate the location of the touchpad and provides a visual representation of the removal procedure.
Removing and installing components
47