HP 170X HP JetDirect 170X - Installation and Configuration Guide - Page 59

HP Jetdirect Configuration Messages

Get HP 170X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300699
View all HP 170X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Table 8.2 Message General HP Jetdirect Messages (1 of 15) Description ARP DUPLICATE IP ADDRESS The ARP layer has detected another node on the network using the same IP address as the HP Jetdirect print server. Extended error information below this message shows the hardware address of the other node. BABBLE ERROR Run the power-on self-test: turn the printer off, then on again. If the error persists, call the HP Support(see Chapter 1 for telephone numbers). BAD BOOTP REPLY An error was detected in the BOOTP reply that the HP Jetdirect print server received. The BOOTP reply either had insufficient data in the UDP datagram to contain the minimum BOOTP header of 236 bytes, had an operation field that was not BOOTPREPLY(0X02), had a header field that did not match the print servers hardware address, or had a UDP source port that was not the BOOTP server port (67/udp). BAD BOOTP TAG SIZE The tagsize in a vendor specific field in the BOOTP reply is either 0, or greater than the remaining number of unprocessed bytes in the vendor specified area. BAD LENGTH RCVD: Total number of frames missed because they were too long for the HP Jetdirect print server to receive. BAD PACKETS RCVD: Total number of frames (packets) received by the HP Jetdirect print server with errors. BOOTP IN PROGRESS The HP Jetdirect print server is currently in the process of obtaining its basic IP configuration information through BOOTP, and has not detected any errors. CF ERR - ACCESS LIST EXCEEDED The TFTP configuration file specified too many access list entries using the "allow:" keyword. CF ERR - FILE INCOMPLETE The TFTP configuration file contained an incomplete last line that did not end in a newline character. CF ERR - INVALID PARAM A line in the TFTP configuration file contained an invalid value for one of the parameters on that line. 8-4 HP Jetdirect Configuration Page Messages

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
8-4 HP Jetdirect Configuration Page Messages
Table 8.2
General HP Jetdirect Messages (1 of 15)
Message
Description
ARP DUPLICATE IP
ADDRESS
The ARP layer has detected another node on
the network using the same IP address as the
HP Jetdirect print server. Extended error information
below this message shows the hardware address of the
other node.
BABBLE ERROR
Run the power-on self-test: turn the printer off, then on
again. If the error persists, call the HP Support(see
Chapter 1 for telephone numbers).
BAD BOOTP REPLY
An error was detected in the BOOTP reply that the
HP Jetdirect print server received. The BOOTP reply
either had insufficient data in the UDP datagram to
contain the minimum BOOTP header of 236 bytes, had
an operation field that was not BOOTPREPLY(0X02),
had a header field that did not match the print servers
hardware address, or had a UDP source port that was
not the BOOTP server port (67/udp).
BAD BOOTP TAG
SIZE
The tagsize in a vendor specific field in the BOOTP
reply is either 0, or greater than the remaining number
of unprocessed bytes in the vendor specified area.
BAD LENGTH
RCVD:
Total number of frames missed because they were too
long for the HP Jetdirect print server to receive.
BAD PACKETS
RCVD:
Total number of frames (packets) received by the
HP Jetdirect print server with errors.
BOOTP IN
PROGRESS
The HP
Jetdirect print server is currently in the process
of obtaining its basic IP configuration information
through BOOTP, and has not detected any errors.
CF ERR - ACCESS
LIST EXCEEDED
The TFTP configuration file specified too many access
list entries using the “allow:” keyword.
CF ERR - FILE
INCOMPLETE
The TFTP configuration file contained an incomplete
last line that did not end in a newline character.
CF ERR - INVALID
PARAM
A line in the TFTP configuration file contained an invalid
value for one of the parameters on that line.