HP 170X HP JetDirect 170X - Installation and Configuration Guide - Page 61

HP Jetdirect Configuration Messages - reset jetdirect

Get HP 170X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300699
View all HP 170X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Table 8.2 Message General HP Jetdirect Messages (3 of 15) Description DISCONNECTING FROM SERVER The server has been shut down because of a configuration change or reset request. This message automatically clears after a few seconds, unless the printer is offline, is in an error state, or is servicing another I/O port or another network protocol. ERR NEGOTIATING BUFFER SIZE A failure was detected when selecting the buffer size to be used when reading print data from the file server. This may indicate a network problem. When the HP Jetdirect print server is configured for multiple file servers, the error is only displayed on the configuration page (also called a self-test page or configuration plot) if none of the file servers was successfully connected. FAIL RESERVING PRINTER NUM The SPX connection to the print server was lost when the HP Jetdirect print server attempted to reserve the printer number. This indicates a possible network problem, or a problem with the print server. Make sure all cables and routers are functioning correctly. Try restarting the print server. FIRMWARE The firmware revision number of the HP Jetdirect print REVISION: X.XX.XX server currently installed in the printer. HP Jetdirect JXXXXX Identifies the HP Jetdirect print server model number. I/O CARD INITIALIZING (INIT) The HP Jetdirect print server is initializing the network protocols. For more information, see the network operating system status line on the configuration page (also called a self-test page or configuration plot). I/O CARD NOT READY There is a problem with the print server or its configuration. Following the I/O CARD NOT READY message is a status message. See this table for a detailed explanation of all status messages. I/O CARD READY The HP Jetdirect print server is connected and awaiting data. 8-6 HP Jetdirect Configuration Page Messages

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
8-6 HP Jetdirect Configuration Page Messages
DISCONNECTING
FROM SERVER
The server has been shut down because of a
configuration change or reset request. This message
automatically clears after a few seconds, unless the
printer is offline, is in an error state, or is servicing
another I/O port or another network protocol.
ERR NEGOTIATING
BUFFER SIZE
A failure was detected when selecting the buffer size to
be used when reading print data from the file server.
This may indicate a network problem.
When the HP Jetdirect print server is configured for
multiple file servers, the error is only displayed on the
configuration page (also called a self-test page or
configuration plot) if none of the file servers was
successfully connected.
FAIL RESERVING
PRINTER NUM
The SPX connection to the print server was lost when
the HP Jetdirect print server attempted to reserve the
printer number. This indicates a possible network
problem, or a problem with the print server. Make sure
all cables and routers are functioning correctly. Try
restarting the print server.
FIRMWARE
REVISION: X.XX.XX
The firmware revision number of the HP Jetdirect print
server currently installed in the printer.
HP Jetdirect
JXXXXX
Identifies the HP Jetdirect print server model number.
I/O CARD
INITIALIZING (INIT)
The HP Jetdirect print server is initializing the network
protocols. For more information, see the network
operating system status line on the configuration page
(also called a self-test page or configuration plot).
I/O CARD NOT
READY
There is a problem with the print server or its
configuration. Following the I/O CARD NOT READY
message is a status message. See this table for a
detailed explanation of all status messages.
I/O CARD READY
The HP
Jetdirect print server is connected and awaiting
data.
Table 8.2
General HP Jetdirect Messages (3 of 15)
Message
Description