HP Digital Sender Flow 8500 User Guide - Page 35

Ping in Progress, 100TX Full

Get HP Digital Sender Flow 8500 PDF manuals and user guides View all HP Digital Sender Flow 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Table 3-6 Jetdirect menus (continued) Menu item Sub-menu item Ping Results Link Speed Sub-menu item Count Print Results Execute Packets Sent Packets Received Percent Lost RTT Min RTT Max RTT Average Ping in Progress Refresh Values and Description Set the count value for this test. Valid values are 0 -100, default is 4. Yes: Print test results. No (default): Do not print test results. Yes: Execute the selected tests.. No (default): Do not execute the selected tests. Number of packets sent. Valid values are 0-65535. Number of packets received. Valid values are 0-65535. Percent of loss. Valid values are 0-100. Valid values are 0-4096. Valid values are 0-4096. Valid values are 0-4096. Yes No Yes No The link speed and communication mode of the Jetdirect server must match the network. The available settings depend on the product and installed Jetdirect server. Select one of the following link configuration settings: CAUTION: If you change the link setting, network communications with the Jetdirect server and network product might be lost. Auto (default): The Jetdirect server uses auto-negotiation to configure itself with the highest link speed and communication mode allowed. If auto-negotiation fails, either the 100TX Half value or the 10T Half value is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.) 10T Half: 10 Mbps, half-duplex operation. 10T Full: 10 Mbps, full-duplex operation. 100TX Half: 100 Mbps, half-duplex operation. 100TX Full: 100 Mbps, full-duplex operation. 100TX Auto: Limits auto-negotiation to a maximum link speed of 100 Mbps. 1000T Full: 1000 Mbps, full-duplex operation. ENWW Basic configuration using the Administration menu 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Table 3-6
Jetdirect menus (continued)
Menu item
Sub-menu item
Sub-menu item
Values and Description
Count
Set the count value for this test. Valid values are 0 –100,
default is 4.
Print Results
Yes
: Print test results.
No
(default): Do not print test results.
Execute
Yes
: Execute the selected tests..
No
(default): Do not execute the selected tests.
Ping Results
Packets Sent
Number of packets sent. Valid values are 0–65535.
Packets Received
Number of packets received. Valid values are 0–65535.
Percent Lost
Percent of loss. Valid values are 0–100.
RTT Min
Valid values are 0–4096.
RTT Max
Valid values are 0–4096.
RTT Average
Valid values are 0–4096.
Ping in Progress
Yes
No
Refresh
Yes
No
Link Speed
The link speed and communication mode of the Jetdirect
server must match the network. The available settings
depend on the product and installed Jetdirect server. Select
one of the following link configuration settings:
CAUTION:
If you change the link setting, network
communications with the Jetdirect server and network
product might be lost.
Auto
(default): The Jetdirect server uses auto-negotiation
to configure itself with the highest link speed and
communication mode allowed. If auto-negotiation fails,
either the
100TX Half
value or the
10T Half
value is set
depending on the detected link speed of the hub/switch
port. (A 1000T half-duplex selection is not supported.)
10T Half
: 10 Mbps, half-duplex operation.
10T Full
: 10 Mbps, full-duplex operation.
100TX Half
: 100 Mbps, half-duplex operation.
100TX Full
: 100 Mbps, full-duplex operation.
100TX Auto
: Limits auto-negotiation to a maximum link
speed of 100 Mbps.
1000T Full
: 1000 Mbps, full-duplex operation.
ENWW
Basic configuration using the Administration menu
27